Installation Instructions Owner manual

ManualsBrandsRockwell Automation ManualsEquipment2711P-RY2032 Battery Replacement

Installation Instructions

Battery Replacement

Catalog Number

2711P-RY2032

About This Publication

This document provides information on how to replace the lithium battery, catalog number

2711P-RY2032, in these devices:

• 2711P PanelView Plus, 700 to 1500 terminals, running FactoryTalk View Machine

Edition firmware revision 5.1 or earlier

• 2711C PanelView Component, C400, C600, and C1000 terminals

• 2711P PanelView™ Plus 6, 400 and 600 terminals

• 2711PC PanelView Plus 6, Compact 400, 600, and 1000 terminals

• 2711P PanelView Plus 7, Standard 400 to 1000 terminals

Topic Page

Important User Information 2

Precautions 3

Replace Battery in PanelView Plus Terminals 3

Replace Battery in PanelView Component Terminals 5

Replace Battery in PanelView Plus 6 and PanelView Plus 6

Compact Terminals

400 and 600 Terminals 5

Replace Battery in PanelView Plus 6 Compact Terminals 7

1000 Terminals 7

Replace Battery in PanelView Plus 7 Standard Terminals 8

Additional Resources 9

IMPORTANT

Use only replacement battery catalog number 2711P-RY2032, or an equivalent CR2032 lithium coin cell

battery, in these products.

Summary of content (12 pages)

PAGE 1
Installation Instructions Battery Replacement Catalog Number 2711P-RY2032 Topic Page Important User Information 2 Precautions 3 Replace Battery in PanelView Plus Terminals 3 Replace Battery in PanelView Component Terminals 5 Replace Battery in PanelView Plus 6 and PanelView Plus 6 Compact Terminals 5 400 and 600 Terminals Replace Battery in PanelView Plus 6 Compact Terminals 1000 Terminals 5 7 7 Replace Battery in PanelView Plus 7 Standard Terminals 8 Additional Resources 9 About This Pub
PAGE 2
Battery Replacement Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
PAGE 3
Battery Replacement 3 Precautions These products contain a sealed lithium battery which may need to be replaced during the life of the product. At the end of its life, the battery contained in this product should be collected separately from any unsorted municipal waste. The collection and recycling of batteries helps protect the environment and contributes to the conservation of natural resources as valuable materials are recovered.
PAGE 4
Battery Replacement 3. Detach the communication module, if attached, from the logic module by removing the four screws. Communication Module Logic Module Screw Captive Screw Display Module 4. Loosen the captive screws that secure the logic module to the display module and carefully lift the logic module away from the back of the display. 5. Locate the battery on the circuit board. 6. Remove the battery by lifting up the side of the battery. 7.
PAGE 5
Battery Replacement 5 10. Tighten the captive screws that secure the logic module to the display module and torque to 0.58…0.79 N•m (5…7 lb•in). 11. Reattach the communication module, if necessary, and tighten the screws to a torque of 0.58…0.79 N•m (5…7 lb•in). Replace Battery in PanelView Component Terminals The PanelView Component C400, C600, and C1000 terminals, catalog numbers 2711C-T4T, 2711C-T6x, and 2711C-T10C, contain a lithium battery on the back of the terminal.
PAGE 6
Battery Replacement 2. Unlatch the battery cover by pulling it straight out. 3. Lift up on the cover. 4. Remove the battery. CR2032 5. Insert the new battery with the positive (+) polarity facing up and press gently until the battery snaps into place. 6. Close the battery cover and push the end in until you hear a click.
PAGE 7
Battery Replacement 7 Replace Battery in PanelView Plus 6 Compact Terminals 1000 Terminals Follow these steps to replace the battery in a 1000 terminal. 1. Disconnect power from the terminal. 2. Place the terminal, display side down, on a flat stable surface. 3. Detach the communication module, if attached, from the logic module by removing the four screws. 4. Loosen the four captive screws that attach the logic module to the display.
PAGE 8
Battery Replacement 11. Push down on the logic module until it is firmly seated. 12. Tighten the four captive screws that secure the logic module to a torque of 0.58 N•m (5…7 lb•in). 13. Reattach the communication module, if necessary, and tighten the four screws to a torque of 0.58 N•m (5…7 lb•in). Replace Battery in PanelView Plus 7 Standard Terminals Follow these steps to replace the battery in PanelView Plus 7 Standard 400 to 1000 terminals. 1. Disconnect power from the terminal. 2.
PAGE 9
Battery Replacement 9 4. Insert the new battery at an angle under the metal latch, with the positive polarity (+) facing up. 5. Gently press down on the opposite side of the battery until it locks into place. IMPORTANT Make sure that the battery is fully inserted under the plastic tabs. If this is not done, damage can occur, and this voids the warranty. 6. Replace the battery cover by aligning its tabs with the battery opening and rotate the cover from the O(pen) to C(lose) position.
PAGE 10
Battery Replacement Notes: Rockwell Automation Rockwell Automation Publication 2711P-IN009F-EN-P - July 2014
PAGE 11
Battery Replacement 11 Notes: Rockwell Automation Rockwell Automation Publication 2711P-IN009F-EN-P - July 2014
PAGE 12
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support you can find technical and application notes, sample code, and links to software service packs. You can also visit our Support Center at https://rockwellautomation.custhelp.com/ for software updates, support chats and forums, technical information, FAQs, and to sign up for product notification updates.