User Manual

ManualsBrandsRockwell Automation ManualsEquipment2711P-RLxxx Backlight Replacement for PVPlus and PVPlus CE Terminals

Publication 2711P-IN019D-EN-P - February 2007

Installation Instructions

Backlight Replacement

Catalog Numbers 2711P-RL7C, 2711P-RL7C2, 2711P-RL10C,

2711P-RL10C2, 2711P-RL12C, 2711P-RL12C2, 2711P-RL15C

About This Publication

This document shows how to remove and replace the backlight for the 700, 1000,

1250, and 1500 versions of the PanelView Plus/PanelView Plus CE terminals. The

1250 High-bright terminals do not have a replaceable backlight.

Topic Page

About This Publication 1

Important User Information 2

Precautions 3

Required Tools 3

Remove Display Module Bezel 3

Replace Backlight 6

Replace Display Module Bezel 10

Summary of content (12 pages)

PAGE 1
Installation Instructions Backlight Replacement Catalog Numbers 2711P-RL7C, 2711P-RL7C2, 2711P-RL10C, 2711P-RL10C2, 2711P-RL12C, 2711P-RL12C2, 2711P-RL15C Topic Page About This Publication 1 Important User Information 2 Precautions 3 Required Tools 3 Remove Display Module Bezel 3 Remove Display Module Bezel 3 Replace Backlight 6 Replace Display Module Bezel 10 About This Publication This document shows how to remove and replace the backlight for the 700, 1000, 1250, and 1500 versions of
PAGE 2
Backlight Replacement Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://literature.rockwellautomation.com) describes some important differences between solid state equipment and hard-wired electromechanical devices.
PAGE 3
Backlight Replacement 3 Precautions Disconnect power from the terminal before installing or replacing any components. Take care not to touch any of the exposed electronic components during installation. ATTENTION ATTENTION Disconnect all power from the terminal before installing or replacing any components. Failure to disconnect power may result in electrical shock or damage to the terminal. Work in a static free environment and wear a properly grounded electrostatic discharge (ESD) wristband.
PAGE 4
Backlight Replacement 4. Disconnect the touch screen connector. Plate Touch Screen Connector 5. Remove the screws from the back of the display module. The number of screws varies for each terminal type. Display Module Bezel 6. Remove the sealing gasket.
PAGE 5
Backlight Replacement 5 7. Lift the back of the display module away from the bezel. IMPORTANT The 700 series C display is not secured by screws and is only retained by a bracket. Use care not to drop the display once the bezel is removed. Work on a clean, flat, stable surface to protect the display from debris, scratches and damage. Display Module Bezel 8. Detach all connectors, maximum of three. The number of connectors varies by model.
PAGE 6
Backlight Replacement Replace Backlight This section shows how to replace the backlight for the 700, 1000, 1250, and 1500 terminals. Backlights for PanelView Plus 700 to 1500 Displays Use Cat. No. For Display Series # of Backlights 2711P-RL7C 700 A and B 1 C 1 A 1 B and C 1 A and B 2 C 1 B 2 2711P-RL7C2 2711P-RL10C 1000 2711P-RL10C2 2711P-RL12C 1250 2711P-RL12C2 2711P-RL15C 1500 Follow these steps to replace the backlight.
PAGE 7
Backlight Replacement 7 4. Detach the backlight connectors from the circuit board. 1250 Backlight Connector 1500 For 700 and 1000 Terminals Work on a clean, flat, stable surface to protect the display from debris, scratches, and damage. 5. Press the retaining tab that secures the backlight and then pull out the backlight.
PAGE 8
Backlight Replacement 6. Insert the new backlight. Backlight For 1250 and 1500 Terminals Work on a clean, flat, stable surface to protect the display from debris, scratches, and damage. 7. Remove the screws that secure the backlights and then remove the backlights. The two backlights for 1250 series A and B displays are each secured with two screws. The single backlight for 1250 series C displays is secured with one screw. Remove the tape, then remove the backlights for the 1500 series B displays.
PAGE 9
Backlight Replacement 9 8. Insert the new backlights and then secure each with the same screws from step 7 and torque to 0.117 Nm (1.04 lb-in). 9. Attach the LCD display connector to the circuit board (shown in step 3 on page 6). 10. Attach the backlight connector to the circuit board (shown in step 4 on page 7). 11. Secure the LCD display. a. Attach the display bracket then secure the display in the bracket for the 700 series C display. b. Attach the four screws for all other displays.
PAGE 10
Backlight Replacement Replace Display Module Bezel Follow these steps to replace the bezel. 1. Make sure bezel is free of lint and marks before reattaching. 2. Attach the following connectors. The number of connectors varies by model. • IrDa connector (if present) • Function key connector • Touch screen connector 3. Place the back of the display module over the bezel. Be careful not to pinch any of the cables. Allow the touch screen connector to extend out of the access opening. 4.
PAGE 11
Backlight Replacement 11 Notes: Publication 2711P-IN019D-EN-P - February 2007
PAGE 12
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://support.rockwellautomation.com, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.