Specifications

ManualsBrandsRockwell Automation ManualsComputer equipment22-WIM-N4S

PARAMETERS (DPI MODE)

No. Name Description

01 DPI Port Displays the port on the host drive which the converter is connected.

02 Reset Module Resets the converter or sets the converter parameters to factory default.

03 Clear DF1 Counts Resets the DF1 statistical Parameter 04 - [DF1 Packets Sent] and Parameter

05 - [DF1 Packets Rcvd] to 0 if set to “1 = Clear Counts”. This parameter will

be reset to “0 = Ready” after a “Clear Counts” command has been performed.

04 DF1 Packets Sent Displays the number of DF1 packets sent by the converter. This parameter is normally

about equal to the value in Parameter 05 - [DF1 Packets Rcvd].

05 DF1 Packets Rcvd Displays the number of DF1 packets received by the converter. This parameter

is normally about equal to the value in Parameter 04 - [DF1 Packets Sent].

06 Interface Mode Selects whether the converter will autodetect DPI or SCANport devices and use

the appropriate protocol.

07 DPI Data Rate Displays the data rate used by the DPI drive. This data rate is set in the drive,

and the converter autobauds to it.

08 Ref/Fdbk Size Displays the size of the Speed Reference/Feedback words which is determined

by the drive. The converter automatically uses the correct size.

09 Datalink Size Displays the size of each Datalink word which is determined by the drive.

The converter automatically uses the correct size.

SPECIFICATIONS

Communications Network Protocol USB

Data Rate 115.2 Kbps

Drive Protocol DPI

Data Rate 125 or 500 Kbps

DSI

19.2 Kbps

SCANport

125 Kbps

Electrical Consumption Drive DPI/SCANport

130 mA at 12 VDC

DSI

170 mA at 5 VDC

Network None

Regulatory UL UL508C

Compliance cUL CAN/CSA C22.2 No. 14-M91

CE EN50178 and EN61800-3

CTick AS/NZS 2064, Group 1, Class A

Route through DPI to drives connected on

BACnet MS/TP (20-COMM-BControlNet (20-COMM-C),

DeviceNet (20-COMM-D), EtherNet/IP (20-COMM-E)

or DF1 (20-COMM-S)

PowerFlex 70 Drives

with 20-COMM-*

Adapters (Port 5)

Route through DSI to drives connected on

ControlNet (22-COMM-C), DeviceNet (22-COMM-D) or

EtherNet/IP (22-COMM-E) in "Master" mode, or Modbus in "RTU Master" mode

PowerFlex 40 Drives with

22-COMM-* Adapters

USB Cable (included)

1203-USB

Converter

22-HIM-H10 (included)

20-HIM-H10 (included)

Laptop or Desktop PC

with DriveExplorer or DriveExecutive

0.00

2.5

646.0

Cans/Sec

Bus/Volt

STS

PORT

MOD

NET A

NET B

0.00

2.5

646.0

Cans/Sec

Bus/Volt

STS

PORT

MOD

NET A

NET B

NETWORK EXAMPLE

No. Name Description

01 Adapter Cfg Sets the operating mode of the converter.

02 Reset Module Resets the converter or sets the converter parameters to factory default.

03 Clear DF1 Counts Resets the DF1 statistical Parameter 04 - [DF1 Packets Sent] and Parameter

05 - [DF1 Packets Rcvd] to 0 if set to “1 = Clear Counts”. This parameter will

be reset to “0 = Ready” after a “Clear Counts” command has been performed.

04 DF1 Packets Sent Displays the number of DF1 packets sent by the converter. This parameter is

normally about equal to the value in Parameter 05 - [DF1 Packets Rcvd].

05 DF1 Packets Rcvd Displays the number of DF1 packets received by the converter. This parameter

is normally about equal to the valu in Parameter 0 - [DF1 Packets Sent].

06 RTU DSI Addr Cfg Sets the node address of the converter for use with the converter operating mode set

with Parameter 01 - [Adapter Cfg].

07 RTU DSI Addr Act Displays the node address of the drive that the converter is communicating with

when the converter is set to RTU Master mode using Parameter 01 - [Adapter Cfg].

08 Adapter Type Displays the present operating mode of the converter.

PARAMETERS (DSI MODE)

No. Name Description

01 Adapter Port Displays the port on the host drive which the converter is connected.