Specifications

PARAMETERS
No. Name Description
01 Mode Displays the mode selected by the jumper on the adapter
(Single or Multi-Drive).
02 BOOTP Sets the DeviceNet node address after a reset or power cycle.
03 IP Addr Cfg 1 Sets the respective bytes in the IP address, where the represented
04 IP Addr Cfg 2
address is: Cfg1.Cfg2.Cfg3.Cfg4.
05 IP Addr Cfg 3
06 IP Addr Cfg 4
07 Subnet Cfg 1 Sets the bytes of the subnet mask, where the represented mask
08 Subnet Cfg 2
is :Cfg1.Cfg2.Cfg3.Cfg4.
09 Subnet Cfg 3
10 Subnet Cfg 4
11 Gateway Cfg 1 Sets the bytes of the gateway address, where the represented
12 Gateway Cfg 2
address is: Cfg1.Cfg2.Cfg3.Cfg4.
13 Gateway Cfg 3
14 Gateway Cfg 4
15 EN Rate Cfg Configures the network data rate at which the adapter communicates.
16 EN Rate Act Displays the data rate actually used by the adapter.
17 Reset Module Used to reset the adapter or set defaults.
18 Comm Flt Action Sets the action that the adapter will take if it detects that
communications have been disrupted.
19 Idle Flt Action Sets the action that the adapter will take if it detects that the scanner is idle.
20 Flt Cfg Logic Sets the data that is sent to the drive if any of the following is true:
21 Flt Cfg Ref
• Parameter 18 - [Comm Flt Action] is set to Send Flt Cfg and
communications are disrupted.
• Parameter 19 - [Idle Fault Action] is set to Send Flt Cfg and the
scanner is put into Program mode.
22 DSI I/O Config Selects the I/O that is transferred through the adapter.
23 DSI I/O Act Displays the I/O that the adapter is actively transmitting.
24 Drv 0 Addr Sets the corresponding node addresses of the daisy-chained drives
25 Drv 1 Addr
used in Multi-Drive mode.
26 Drv 2 Addr
27 Drv 3 Addr
28 Drv 4 Addr
29 Web Enable Displays the setting of the web pages switch on the adapter when the
adapter was last reset. (Enables/Disables using web pages)
30 Web Features Sets the access to the web interface and web configurable features.
SPECIFICATIONS
Communications Network Protocol EtherNet/IP
Data Rates 10/100 Mbps, Full/Half Duplex
Drive Protocol DSI
Electrical Consumption Drive (DPI) 350 mA at 5 VDC
Network N/A
Regulatory UL UL508C
Compliance cUL CAN/CSA C22.2 No. 14-M91
CE EN50178 and EN61800-3
EXAMPLE I/O IMAGE - SINGLE MODE
Controller
Scanner
Adapter
Word and I/O
PowerFlex 40 Drive
EtherNet/IP
DSI
Output
Image
(Write)
Input
Image
(Read)
Message
Handler
Message
Buffer
0 Logic Status
1 Feedback
Logic Status
Feedback
Message
Handler
0 Logic Command
1 Reference
Logic Command
Reference
Controller
Scanner Adapter
Word and I/O
EtherNet/IP
DSI
Output
Image
(Write)
Input
Image
(Read)
Message
Handler
Message
Buffer
0 Logic Command
1 Reference
2 Logic Command
3 Reference
4 Logic Command
5 Reference
6 Logic Command
7 Reference
8 Logic Command
9 Reference
0 Logic Status
1 Feedback
2 Logic Status
3 Feedback
4 Logic Status
5 Feedback
6 Logic Status
7 Feedback
8 Logic Status
9 Feedback
PowerFlex Drive 2
PowerFlex Drive 0
PowerFlex Drive 1
PowerFlex Drive 3
PowerFlex Drive 4
PowerFlex Drive 0
PowerFlex Drive 1
PowerFlex Drive 2
PowerFlex Drive 3
PowerFlex Drive 4
EXAMPLE I/O IMAGE - MULTI-DRIVE MODE
22comm_E_PP_NL_8_23.qxd:Product_app_profile5-18-05.qxd 8/23/06 1:52 PM Page 2