User manual

AC Adjustable Frequency Drives
Important Safety and Product Information
162
CSA Certification
In many cases Rockwell Automation pursues applicable CSA
certifications for its products. CSA certifies products for general
use as well as for use in hazardous locations. Products in this
catalog might be certified in one of these two ways:
y CSA Certification (CSA): The product is certified by the
Canadian Standards Association for use in Non-hazardous
Locations.
y CSA Class I, Division 2 Hazardous Location Certification: The
product is listed by the Canadian Standards Association as
certified for use in Class I, Division 2, Group A, B, C, D, or
non-hazardous locations.
Although Rockwell Automation is only using the Class I Division
2 Group A, B, C, D designation on its products, it should be noted
that this hazardous location classification is equivalent to the
internationally defined Class I Zone 2 Group IIC area
classification (see IEC publication 60079-10). Therefore, products
labeled Class I Division 2 Group A, B, C, D may be used in Class
I Zone 2 Group IIC environments.
Actual CSA certification is indicated by the marking on the
product, and not by statements in this catalog or any product
literature.
FM Approval
A limited number of Allen-Bradley branded products have Factory
Mutual Approval. FM approves products for use in general as well
as hazardous locations.
y FM Class I Division 2 Hazardous Location Approval: The
product is approved by Factory Mutual Research Corporation for
use in Class I, Division 2, Group A, B, C, and D, or non-
hazardous locations only.
Although Rockwell Automation is only using the Class I Division
2 Group A, B, C, D designation on its products, it should be noted
that this hazardous location classification is equivalent to the
internationally defined Class I Zone 2 Group IIC area
classification (see IEC publication 60079-10). Therefore, products
labeled Class I Division 2 Group A, B, C, D may be used in Class
I Zone 2 Group IIC environments.
Actual FM Approval is indicated by the marking on the
product, and not by statements in this catalog or any product
literature.
Compliance with European Union Directives
Allen-Bradley branded products covered by European Union
Directives are intended for sale and use within the European
market and conform to the essential requirements of these
directives:
y Products specifically required to do so bear the CE marking per
the relevant European Union Directives and CE marking
regulations.
y Declarations of Conformity for Allen-Bradley branded products
are available as required at www
.ab.com/certification.
y The necessary technical documentation is on file within
Rockwell Automation.
Actual European Union conformity is indicated by the CE
Marking on the product or its packaging, and not by
statements in this catalog or any product literature.
DEMKO Certification
In addition to the "CE" mark, a limited number of Allen-Bradley
branded products have DEMKO certification (D). DEMKO
certifies products for general use as well as hazardous locations.
As a Notified Body for the European Hazardous Location
Directives, DEMKO verifies that products comply with the
applicable European directives and standards for use in hazardous
locations. Refer to the specific product nameplate for the actual
hazardous location rating.
Actual DEMKO approval of product is indicated by the
marking on the product, and not by statements in this catalog
or any product literature.
Certification for Marine and Off-Shore
Applications
If a product or its packaging has a certification for marine and off-
shore applications, it is listed in the Marine Certification
Applications publication CIG-2.2. Also see
www
.ab.com/certification.
y Lloyd's Register
y Registoro Italiano Navale
y Germanischer Lloyd
y Korean Register of Shipping
y American Bureau of Shipping
y Bureau Veritas
y Det Norske Veritas
EU Hazardous Location Certification
In addition to the "CE" mark, a limited number of Allen-Bradley
branded products have also been issued Type Examination
Certificates (Ex) indicating that the products have been found to
comply with the Essential Health and Safety Requirements related
to their design and construction as Category 1, 2, or 3 equipment
intended for use in potentially explosive atmospheres as given in
Annex II of EU Directive 94/9/EC. The related hazardous location
protection methods and installation restrictions are documented in
the product user documentation. See www
.ab.com/certification.
Actual approval of product for use in EU Hazardous
(classified) locations is indicated by the marking on the
product, and not by statements in this catalog or any product
literature.
Many Allen-Bradley branded products, such as selected PLC-5
programmable controllers, 1771 I/O, and Dataliner Message
Displays, have been certified for use in marine and offshore
applications around the world by: