User manual

AC Adjustable Frequency Drives
PowerFlex 700
100
Packaged Drives Programs
Control Interface & Feedback Options
Description
Option
Code
Analog Inputs/Outputs
Isolated Analog Input, 0-10V dc
-N1 7
Isolated Analog Input, 4-20 mA
-N2 7
Isolated Analog Output, 0-10V dc
-N3 7
Control Relay Option
Control Power On
-J1 7
Auxiliary Contacts, (2) Form C 2-N.O., 2-N.C.
✶
Drive Fault
-J2 7
Alarm
-J3 7
Drive Run
-J4 7
At Speed
-J5 7
Programmable Relay A
-J6 7
Programmable Relay B
-J7 7
Building Management Control Interface
-N5 7
Communication Options Panel Mounted
Johnson Controls Metasys Interface
-G1 7
✶ Maximum of two drive digital options can be selected.
NOTE: S9 + J4 = One Digital Output
S10 + J2 = One Digital Output
S11 + J5 = One Digital Output
S12 + J3 = One Digital Output
All other combinations = One Digital Output.
7 This requires option -C1 or user supplied 115V (option -C5).
Motor Interface Options
Description
Option
Code
Motor Heater Control
-J8 ‡
‡ Requires user supplied control power.
Meters - Door Mounted
Description
Option
Code
Drive/Bypass Motor Run Time Meter (Elapsed Hours) Non-
Resettable
-M3 7
7 This requires option -C1 or user supplied 115V (option -C5).
Codes and Standards
Code/Standard Action
CE 
(European Conformance
Standard)
Consult the factory with
requirements to meet the
separate Low Voltage and/or
EMC directives.
IEEE519 
(Harmonic Distortion Levels)
Provide a one-line power
distribution drawing, and the
associated specification to the
factory, for review.
UL, c-UL (CSA)
This program provides UL panel
recognition from the factory as
standard.
 Engineered Drives Program Only
Operator Devices - Door Mounted
Description
Option
Code
H/O/A S.S. (Start/Stop/Spd. Ref.)
-S1 a
Run Pilot Light
-S9 ✶ 7
Drive Fault Pilot Light
-S10 ✶ 7
At Speed Pilot Light
-S11 ✶ 7
Drive Alarm Pilot Light
-S12 ✶ 7
Control Power On Pilot Light
-S13 7
Drive & Bypass Mode Pilot Lights
-S14 7 ♣
Bypass Mode & Auto Bypass En. P.L.
-S15 7➤
Drive Disable Mushroom P.B.
-S16 a
Motor Fault Pilot Light
-S17 7♣
✶ Maximum of two drive digital options can be selected.
NOTE: S9 + J4 = One Digital Output
S10 + J2 = One Digital Output
S11 + J5 = One Digital Output
S12 + J3 = One Digital Output
All other combinations = One Digital Output.
7 This requires option -C1 or user supplied 115V (option -C5).
♣ Option available when -B1 is selected.
➤ Option available when -B2 is selected.
a Does not require option -C1 or user supplied power (-C5) if 24V ac/dc
interface is selected. Requires option -C1 or user supplied power (-C5), if
115V ac interface is selected.
Enclosure Options
Description
Option
Code
Nameplate, Door Mounted 158.8 x 50.8 mm (6.25 x 2 in.)
white Lamacoid with black letters)
-E9 
UL Type 3/4/12
Consult
Factory
 Actual message to be defined by user at order entry, otherwise will be
supplied blank.