Owner's manual

Rockwell Automation Publication 20P-UM001I-EN-P - February 2013 183
Programming and Parameters Chapter 3
INPUT / OUTPUT
Digital Inputs
133
134
135
136
137
138
139
140
141
142
143
144
[Digital In1 Sel]
[Digital In2 Sel]
[Digital In3 Sel]
[Digital In4 Sel]
[Digital In5 Sel]
[Digital In6 Sel]
[Digital In7 Sel]
[Digital In8 Sel]
[Digital In9 Sel]*
[Digital In10 Sel]*
[Digital In11 Sel]*
[Digital In12 Sel]*
Selects the function driven by the digital input.
See Option Definitions for [Digital Inx Sel] on page 184.
*These parameters are used to configure the digital inputs on the I/O
Expansion circuit board. Do not use these parameters if the I/O Expansion
circuit board is not
installed.
Notes: Option 35 was changed from “Fld Weaken En” and option 64 “Invert
Flt” was added for firmware version 2.001. Option 34 “Field Reg En” was
changed for firmware version 3.001.
Options:
Default:
Default:
Default:
Default:
Default:
Default:
Default:
Default:
Default:
Default:
Default:
Default:
2 =
3 =
11 =
1 =
17 =
18 =
19 =
31 =
0 =
0 =
0 =
0 =
“Stop/CF”
“Start”
“Jog”
“Enable”
(1)
“Speed Sel 1”
“Speed Sel 2”
“Speed Sel 3”
“Contactor”
“Not Used”
“Not Used”
“Not Used”
“Not Used”
16-bit
Int
(1) A digital input (1…8 only) must be configured for “Enable”.
(2) For digital inputs 9…12, this option displays as “Reserved”, indicating that it is not available for use - do not select “Reserved” options.
(3) Not used for permanent magnet motor applications.
(4)
(5)
File Group No.
Parameter Name & Description
See page 110 for symbol descriptions
Values
Data Type Related
0 = “Not Used” (Off) 17 = “Speed Sel 1” 34 = “Reserved” 51 = “Diam Reset”
1 = “Enable”
(1)(2)
18 = “Speed Sel 2” 35 = “Force MinFld”
(3)(4)
52 = “DiamCalc Dis”
2 = “Stop/CF”
(2)
19 = “Speed Sel 3” 36 = “Freeze Ramp” 53 = “Torq Wind En”
3 = “Start”
(2)
20 = “PI Enable” 37 = “UsrDefinedA0” 54 = “Speed Match”
4 = “Fwd/Reverse”
(2)
21 = “PI Hold” 38 = “UsrDefinedA1” 55 = “Diam I/D En”
5 = “Run”
(2)
22 = “PI Reset” 39 = “UsrDefinedA2” 56 = “Wind/Unwind”
6 = “Run Forward”
(2)
23 = “PI Invert” 40 = “UsrDefinedA3” 57 = “Diam Preset0”
7 = “Run Reverse”
(2)
24 = “Local” 41 = “UsrDefinedA4” 58 = “Diam Preset1”
8 = “Run Level”
(2)
25 = “Acc2 & Dec2” 42 = “UsrDefinedA5” 59 = “Taper Enable”
9 = “RunFwd Level”
(2)
26 = “Accel 2” 43 = “UsrDefinedA6” 60 = “Spd DemandEn”
10 = “RunRev Level”
(2)
27 = “Decel 2” 44 = “UsrDefinedA7” 61 = “Winder Side”
11 = “Jog”
(2)
28 = “MOP Inc” 45 = “Droop Enable” 62 = “PI-PD Enable”
12 = “Jog Forward”
(2)
29 = “MOP Dec” 46 = “PD Enable” 63 = “Jog TW En”
13 = “Jog Reverse”
(2)
30 = “Fast Stop” 47 = “PID SetptSel” 64 = “Invert Flt”
14 = “Aux Fault” 31 = “Contactor”
(5)
48 = “PI Cent vs0”
15 = “Clear Faults” 32 = “MOP Reset” 49 = “PI Cent vs1”
16 = “Auto/Manual” 33 = “TorqueReduce” 50 = “Diam Calc”
ATTENTION: Enabling (forcing) the minimum field current while the drive is running could result in excessive
motor speed, equipment damage and/or bodily injury.
ATTENTION: Contactor status should only be used by the drive. It should not be used to initiate any external
action (e.g., mechanical braking), or equipment damage and/or bodily injury may occur.