Owner manual

ManualsBrandsRockwell Automation ManualsEquipment20D Lifting Mounting PowerFlex 700S and 700H Drives (Frame 10 - 14)

Installation Instructions

Lifting & Mounting PowerFlex

700S and 700H

Drives (Frames 10 - 14)

General Precautions

What You Need to Do

❐ Step 1: Attach the lifting hardware to the drive

❐ Step 2: Remove the skid and shipping feet

❐ Step 3: Mount the drive to the floor and/or wall

❐ Step 4: For AC input frame 14 drives only, connect the two enclosure

sections with the kit provided.

ATTENTION: To guard against possible personal injury and/or

equipment damage…

• Do Not allow any part of the drive or lifting mechanism to

make contact with electrically charged conductors or

components.

• At no time should a person or their limbs be directly

underneath the items being lifted.

• Do not subject the load to high rates of acceleration or

deceleration.

• Inspect all lifting hardware for proper attachment before

lifting the drive unit.

Summary of content (10 pages)

PAGE 1
Installation Instructions Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) General Precautions ! What You Need to Do ATTENTION: To guard against possible personal injury and/or equipment damage… • Do Not allow any part of the drive or lifting mechanism to make contact with electrically charged conductors or components. • At no time should a person or their limbs be directly underneath the items being lifted. • Do not subject the load to high rates of acceleration or deceleration.
PAGE 2
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Frame 14 Drive Enclosure Sections AC Input frame 14 drives are shipped as multiple enclosure sections that must be lifted separately and then connected after they have been properly mounted. ! ATTENTION: Do Not lift frame 14 drive enclosure sections after they have been connected as one unit.
PAGE 3
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Step 1: Attaching the Lifting Hardware to the Drive Directions for Drives Installed in Standard Rittal Enclosures A Note: Lift each Frame 14 drive enclosure section separately. Refer to Frame 14 Drive Enclosure Sections on page 2 for more information. B OR C B>A Min.
PAGE 4
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Drive Frame Voltage Rating Size Class Amps 13 400 1150 1300 1450 600 920 1030 1180 AC Input Drive & Enclosure Weight kg (lbs.) 1348 (2972) 1400 (3086) 1400 (3086) 1248 (2751) 1248 (2751) 1248 (2751) AC Input Drive, Enclosure & Packaging Weight - kg (lbs.) 1468 (3236) 1520 (3351) 1520 (3351) 1368 (3016) 1368 (3016) 1368 (3016) DC Input Drive & Enclosure Weight kg (lbs.
PAGE 5
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Directions for Open Type Drives B ! A . and death tes cing. use. e k and 5 minue servibefor shocr, wait befor al ric ge manu elect t powevolta s in of bus ction red. Risk nnec Disco DC instru d requi verify w groun Follo Earth DA NG ER C D AC Choke Fasten the module symmetrically in at least two (2) holes. ! DAN GER Risk of electric Disconne shock ct power, and verify death.
PAGE 6
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Drive Drive Frame Voltage Rating Size Class Amps 12 400 820 920 1030 600 650 750 820 (1) (2) (3) (4) Power Structure Weight - kg (lbs.) 120 (265)(1) 120 (265)(1) 120 (265)(1) 120 (265)(1) 120 (265)(1) 120 (265)(1) AC Input Drive & Packaging Weight kg (lbs.)(4) 350 (772) 350 (772) 350 (772) 288 (635) 288 (635) 288 (635) AC Choke Weight kg (lbs.
PAGE 7
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Step 2: Removing the Skid and Shipping Feet ! Task A 7 ATTENTION: To guard against personal injury and equipment damage, do not work under the drive unless the drive is securely mounted on appropriate blocks. Description Using a 15 mm wrench, remove the hardware that secures the drive to the skid. A B Lift the drive off of the skid. A C Place the drive on proper blocks on a hard level surface.
PAGE 8
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Step 3: Mounting the Drive Floor Only Mounting to the Floor and/or Wall Secure the drive to the floor with anchor bolts in the front corner holes of the enclosure base plate. Additionally, secure the drive using the mounting plates as needed (Rittal part no. 8800-210 or equivalent). Do this as close as possible to the choke assembly plate. With this method, the holes through the base plate must be drilled on site.
PAGE 9
Lifting & Mounting PowerFlex® 700S and 700H Drives (Frames 10 - 14) Step 4: Connecting Frame Complete the procedures detailed in the documentation included in the kit 14 Drive Enclosure Sections provided with the drive.
PAGE 10
Notes: www.rockwellautomation.com Power, Control and Information Solutions Headquarters Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204 USA,Tel: (1) 414.382.2000, Fax: (1) 414.382.