Owner's manual

ManualsBrandsRockwell Automation ManualsEquipment20D-DL2-CL3 DriveLogix Controller Compact I/O Cable

Publication 20D-IN008B-EN-P - August 2004

Installation Instructions

Compact I/O Cable for

DriveLogix

™

5730 Controller

(Cat. No. 20D-DL2-CR3, 20D-DL2-CL3)

Inside ...

For More Information .............................. 2

Hazardous Location Considerations ........ 3

Overview ................................................ 3

Cable Types and Length .......................... 4

System Configurations ............................ 5

Installation .............................................. 6

Summary of content (12 pages)

PAGE 1
Installation Instructions Compact I/O Cable for DriveLogix™5730 Controller (Cat. No. 20D-DL2-CR3, 20D-DL2-CL3) Inside ... For More Information .............................. Hazardous Location Considerations ........ Overview ................................................ Cable Types and Length .......................... System Configurations ............................ Installation ..............................................
PAGE 2
Compact I/O Cable for DriveLogix™5730 Controller For More Information For Refer to this Document Pub. No.
PAGE 3
Compact I/O Cable for DriveLogix™5730 Controller For Refer to this Document 3 Pub. No.
PAGE 4
Compact I/O Cable for DriveLogix™5730 Controller Cable Types and Length Cables for Connecting Controllers to I/O Banks Catalog Number Cable Type 20D-DL2-CL3 20D-DL2-CR3 Controller-to-left bank expansion Controller-to-right bank expansion (1) Length(1) 3.28 ft. (1 m) 3.28 ft. (1 m) Approximate cable length is measured from end-to-end of the cable only. 32 mm (1.26 in.) 15 mm (0.59 in.) 18 mm (0.71 in.) 118 mm (4.65 in.) 118 mm (4.65 in.
PAGE 5
4 3 2 1 2 3 1769 End Cap 1769 I/O 1769 Power Supply Bank 1 PowerFlex 700S Drive 1769 I/O 1769-CRL3 1769-CRL3 1769 I/O 1769 Power Supply 1 DriveLogix Bank 2 20D-DL2-CR3 1 PowerFlex 700S Drive DriveLogix 20D-DL2-CL3 1769 I/O PowerFlex 700S Drive DriveLogix I/O Slot Number 1769 I/O 1 1769 Power Supply 2 20D-DL2-CR3 1769 I/O 1769 Power Supply 1769 End Cap 1769 I/O I/O Slot Number 1769-CRl3 1769 I/O 1769-CRl3 1769 I/O 1769 Power Supply 1769 End Cap 1769 I/O 1769 End Cap 17
PAGE 6
Compact I/O Cable for DriveLogix™5730 Controller Installation Remove Power ATTENTION ! To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC & –DC terminals of the Power Terminal Block. The voltage must be zero. HOT surfaces can cause severe burns. Do not touch the heatsink surface during operation of the drive. After disconnecting power allow time for cooling.
PAGE 7
Compact I/O Cable for DriveLogix™5730 Controller 7 What You Need to Do ❐ Step 1: Remove power from drive and Compact I/O ❐ Step 2: Remove the control cassette from the drive and the cover from the control cassette ❐ Step 3: Install the controller end of the cable ❐ Step 4: Replace the cover and control cassette ❐ Step 5: Connect the Compact I/O end of the cable Publication 20D-IN008B-EN-P - August 2004
PAGE 8
Compact I/O Cable for DriveLogix™5730 Controller Step 1: Removing Power from Drive and Compact I/O ATTENTION ! To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC & –DC terminals of the Power Terminal Block. The voltage must be zero. Remove power before making or breaking cable connections.
PAGE 9
Compact I/O Cable for DriveLogix™5730 Controller 9 Step 2: Removing the Control Cassette from the Drive and the Covers from the Cassette Removing the Cassette B Task A B B C A Description Open the door of the power structure and disconnect the cables that connect to the main board Loosen screws on face of cassette Remove the cassette 1 BR 2 BR PE L2 DC DC- + U/ V/ T1 W T2 R/L1 /T3 C = Proper tightening torque for reassembly is 6 lb.-in.
PAGE 10
Compact I/O Cable for DriveLogix™5730 Controller Step 3: Installing the Controller End of the Cable A D Task B C A D A B B C D E Description Remove screws Install clips on controller end of cable Plug controller end of cable into mating connector on the Logix Expansion Board Install and tighten screws (7-10 lb.-in.
PAGE 11
Compact I/O Cable for DriveLogix™5730 Controller 11 Step 5: Installing the Compact I/O End of the Cable ATTENTION ! When energized bus connections break in hazardous environments, resulting sparks can cause explosions. Risk of personal injury and/or equipment damage exists. Securely lock the bus connectors (tasks D and E below) to avoid this hazard.
PAGE 12
TIP Each I/O bank requires its own power supply. The 1769 cables extend the 1769 communication bus, but do not extend bus power. Specifications Approximate Shipping Weight (with carton) 3-foot cables: 350 g (0.77lbs.) Storage Temperature -40°C to +85°C (-40°F to +185°F) Operating Temperature 0°C to +60°C (32°F to +140°F) Operating Humidity 5% to 95% non-condensing Operating Altitude 2000 meters (6561 feet) Vibration Operating: 10 to 500 Hz, 5G, 0.