User guide

ManualsBrandsRockwell Automation ManualsEquipment2090-CPxxx Standard Power Cables with SpeedTec DIN Connector Type 923

Installation Instructions

Standard Power Cables with

SpeedTec DIN Connector Type 923

Catalog Number 2090-CPBM7DF-12AAxx, 2090-CPBM7DF-14AAxx,

2090-CPBM7DF-16AAxx, 2090-CPWM7DF-12AAxx,

2090-CPWM7DF-14AAxx, 2090-CPWM7DF-16AAxx

About Standard Power Cables

Standard motor power cables, with or without brake connections, have a 23 mm (0.9 in.)

SpeedTec DIN connector at the motor end, and flying leads at the drive end. These cables can be

bent or reformed during installation or maintenance, but should not be used in a continuous flex

operation.

Topic Page

Important User Information 2

Before You Begin 3

Install Cables 4

Connector Pinout Diagrams 6

Specifications 7

Additional Resources 8

Summary of content (8 pages)

PAGE 1
Installation Instructions Standard Power Cables with SpeedTec DIN Connector Type 923 Catalog Number 2090-CPBM7DF-12AAxx, 2090-CPBM7DF-14AAxx, 2090-CPBM7DF-16AAxx, 2090-CPWM7DF-12AAxx, 2090-CPWM7DF-14AAxx, 2090-CPWM7DF-16AAxx Topic Page Important User Information 2 Before You Begin 3 Install Cables 4 Connector Pinout Diagrams 6 Specifications 7 Additional Resources 8 About Standard Power Cables Standard motor power cables, with or without brake connections, have a 23 mm (0.9 in.
PAGE 2
Standard Power Cables with SpeedTec DIN Connector Type 923 Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls, publication SGI-1.1, available from your local Rockwell Automation sales office or online at http://rockwellautomation.
PAGE 3
Standard Power Cables with SpeedTec DIN Connector Type 923 3 Before You Begin Remove all packing material from within and around the item. After unpacking, verify the catalog number against the purchase order, and visually inspect the cable and each connector for damage. If necessary, notify the carrier of any shipping damage immediately. Cables are stored and shipped in a coil, and will retain this shape unless you allow the cable to straighten itself.
PAGE 4
Standard Power Cables with SpeedTec DIN Connector Type 923 ATTENTION: The examples in this publication show all the available connections, some of which may not be appropriate for your specific installation. Refer to your drive installation or user manual for recommended wire trim lengths, and wiring examples appropriate to your drive and motor application. Do not connect unused wires.
PAGE 5
Standard Power Cables with SpeedTec DIN Connector Type 923 5 2. Keep cable bends within the bend radius specified on page 7. Never bend a cable tighter than the specified bend radius. Refer to Specifications for the correct value. 3. When installing the cable observe these restrictions: • The bend zone is the area where the cable can be bent to its specified bend radius.
PAGE 6
Standard Power Cables with SpeedTec DIN Connector Type 923 Connector Pinout Diagrams These diagrams provide wire colors and pinouts for the standard power cables. 2090-CPBM7DF-xxAAxx To Motor C D H U V W (2) PE (1) A 18 AWG White 18 AWG Black F G F E Brown (1) Black (1) Blue (1) Green/Yellow A B C D B G To Drive L MBRK+ MBRK- Shield Twisted Wire Pair Connector Backshell Shielded 360° 360° shield-to-ground connections required.
PAGE 7
Standard Power Cables with SpeedTec DIN Connector Type 923 7 Specifications Additional specifications for each cable are available in the Kinetix Motion Control Selection Guide, publication GMC-SG001. 2090-CPBM7DF-xxAAxx Specifications Attribute Value Wire Size 16 AWG 14 AWG 12 AWG Diameter 11.6 mm (0.47 in.) 12.7 mm (0.50 in.) 14.3 mm (0.56 in.) 115 mm (4.5 in.) 130 mm (5.0 in.) 145 mm (6.0 in.) Bend Radius Installation Areas (1) (1) The installation areas are approximately 300 mm (12 in.
PAGE 8
Additional Resources These documents contain additional information concerning related Rockwell Automation products. Kinetix 300 EtherNet/IP Indexing Servo Drive User Manual, publication 2097-UM001 Kinetix 2000 Multi-axis Servo Drive User Manual, publication 2093-UM001 Provides mounting, wiring, configuring, and troubleshooting information for these Kinetix motion control drive systems.