Instruction Manual

ManualsBrandsRockwell Automation ManualsEquipment2090-CPxxx Continuous-flex Power and Brake Extension Cable with DIN Connector

Installation Instructions

Continuous-flex Power and Brake

Extension Cable with SpeedTec

Connector

Catalog Numbers 2090-CPBM7E7-16AFxx, 2090-CPBM7E7-14AFxx,

2090-CPBM7E7-10AFxx, 2090-CPBM7E7-08AFxx

About Continuous-flex Power and Brake Extension Cables

Continuous-flex power with brake extension cables can be repeatedly flexed within a specified

bend radius when properly installed. A circular SpeedTec-ready receptacle and/or a SpeedTec

plug is attached to the cable.

Topic Page

About Continuous-flex Power and Brake Extension Cables 1

Important User Information 2

Before You Begin 3

Install Cables 4

Schematics and Connector Pinouts for Cables 6

Specifications 7

Additional Resources 8

Summary of content (8 pages)

PAGE 1
Installation Instructions Continuous-flex Power and Brake Extension Cable with SpeedTec Connector Catalog Numbers 2090-CPBM7E7-16AFxx, 2090-CPBM7E7-14AFxx, 2090-CPBM7E7-10AFxx, 2090-CPBM7E7-08AFxx Topic Page About Continuous-flex Power and Brake Extension Cables 1 Important User Information 2 Before You Begin 3 Install Cables 4 Schematics and Connector Pinouts for Cables 6 Specifications 7 Additional Resources 8 About Continuous-flex Power and Brake Extension Cables Continuous-flex power wi
PAGE 2
Continuous-flex Power and Brake Extension Cable with SpeedTec Connector Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls, publication SGI-1.1, is available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.
PAGE 3
Continuous-flex Power and Brake Extension Cable with SpeedTec Connector 3 Before You Begin Remove all packing material from within and around the item. After unpacking, verify the catalog number against the purchase order, and visually inspect the cable and each connector for damage. If necessary, notify the carrier of any shipping damage immediately. Cables are stored and shipped in a coil, and will retain this shape unless you allow the cable to straighten itself.
PAGE 4
Continuous-flex Power and Brake Extension Cable with SpeedTec Connector Install Cables Follow these steps when installing a cable. 1. Provide the recommended installation areas, and the correct offset from features, before beginning any cable bend. Features include these areas on the cable: • Connectors • Transitions from exposed wire to insulation (for example, flying leads) • Exposed cable ground shields The offset from these areas should be greater than or equal to (>1x) the cable diameter. 2.
PAGE 5
Continuous-flex Power and Brake Extension Cable with SpeedTec Connector 5 5. Remove the O-ring from the motor receptacle when using a cable with a SpeedTec plug. The type of plug on the cable determines whether an O-ring is required on the receptacle. SpeedTec Plug Remove O-ring when mating with a SpeedTec plug. If an O-ring is installed, a SpeedTec plug will not engage with the receptacle. Threaded Plug Install O-ring when mating with a threaded plug. O-ring in Groove.
PAGE 6
Continuous-flex Power and Brake Extension Cable with SpeedTec Connector Schematics and Connector Pinouts for Cables Wire colors and connector pinouts necessary to connect the cable to a servo system are shown in the schematics. 2090-CPBM7E7-xxAFxx Cables This power with brake cable is available in several wire gauges and lengths. The type of SpeedTec connector varies with the wire gauge.
PAGE 7
Continuous-flex Power and Brake Extension Cable with SpeedTec Connector 7 Specifications These specifications provide information that is useful when installing a cable. Additional specifications are available in the Kinetix Motion Control Selection Guide, publication GMC-SG001. 2090-CPBM7E7-xxAFxx Cables Attribute 2090-CPBM7E716AFxx Wire size 16 AWG Diameter 12.5 mm (0.50 in.) 150 mm (6.0 in.) 125 mm (5.0 in.
PAGE 8
Additional Resources These documents contain additional information concerning related Rockwell Automation products. Resource Description Kinetix 300 EtherNet/IP Indexing Servo Drives User Manual, publication 2097-UM001 How to install, set up, and troubleshoot a servo-drive system.