Owner's manual

ManualsBrandsRockwell Automation ManualsEquipment2090-CFxxx Standard Feedback Cables with SpeedTec DIN Connector Type 623

Table Of Contents

Standard Feedback Cables with SpeedTec DIN Connector Type 623 Installation Instructions, 2090-IN029A-EN-P September 2010

Installation Instructions

Standard Feedback Cables with

SpeedTec DIN Connector Type 623

Catalog Number 2090-CFBM7DD-CEAAxx, 2090-CFBM7DF-CEAAxx

About Standard Feedback Cables

Standard motor feedback cables have a 23 mm (0.9 in.) SpeedTec DIN connector at the motor

end, and a D-sub connector or flying leads at the drive end. These cables can be bent or reformed

during installation or maintenance, but should not be used in a continuous flex operation.

Topic Page

Important User Information 2

Before You Begin 3

Install Cables 4

Schematics and Connector Pinouts for Cables 5

Specifications 7

Additional Resources 8

Summary of content (8 pages)

PAGE 1
Installation Instructions Standard Feedback Cables with SpeedTec DIN Connector Type 623 Catalog Number 2090-CFBM7DD-CEAAxx, 2090-CFBM7DF-CEAAxx Topic Page Important User Information 2 Before You Begin 3 Install Cables 4 Schematics and Connector Pinouts for Cables 5 Specifications 7 Additional Resources 8 About Standard Feedback Cables Standard motor feedback cables have a 23 mm (0.9 in.) SpeedTec DIN connector at the motor end, and a D-sub connector or flying leads at the drive end.
PAGE 2
Standard Feedback Cables with SpeedTec DIN Connector Type 623 Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls, publication SGI-1.1, available from your local Rockwell Automation sales office or online at http://rockwellautomation.
PAGE 3
Standard Feedback Cables with SpeedTec DIN Connector Type 623 3 Before You Begin Remove all packing material from within and around the item. After unpacking, verify the catalog number against the purchase order., and visually inspect the cable and each connector for damage. If necessary, notify the carrier of any shipping damage immediately. Cables are stored and shipped in a coil, and will retain this shape unless you allow the cable to straighten itself.
PAGE 4
Standard Feedback Cables with SpeedTec DIN Connector Type 623 Install Cables Follow these steps when installing a cable. 1. Identify the recommended installation areas and the correct offset from features before beginning any cable bend. Features include these areas on the cable: • Connectors • Transitions from exposed wire to insulation (for example, flying leads) • Exposed cable ground shields The offset from these features should be greater than or equal to (>1x) the cable diameter. 2.
PAGE 5
Standard Feedback Cables with SpeedTec DIN Connector Type 623 5 Schematics and Connector Pinouts for Cables Schematics show wire colors and connector pinouts necessary to connect the cable to a servo system. 2090-CFBM7DD-CEAAxx This cable is available in several lengths. Refer to the Kinetix Motion Control Selection Guide, publication GMC-SG001, for this information and additional specifications.
PAGE 6
Standard Feedback Cables with SpeedTec DIN Connector Type 623 2090-CFBM7DF-CEAAxx This cable is available in several lengths. Refer to the Kinetix Motion Control Selection Guide, publication GMC-SG001, for this information and additional specifications.
PAGE 7
Standard Feedback Cables with SpeedTec DIN Connector Type 623 7 O-ring Removal Remove the O-ring on the motor connector when using a feedback cable, such as the 2090-CFBM7DD-CEAAxx or 22090-CFBM7DF-CEAAxx cable, that has a SpeedTec feedback plug. The type of plug on the feedback cable determines whether an O-ring is required on the feedback receptacle. With This Plug Do This SpeedTec Plug Remove the O-ring from an extension cable receptacle (shown) or a motor connector that is SpeedTec ready.
PAGE 8
Additional Resources These documents contain additional information concerning related Rockwell Automation products. Kinetix 300 EtherNet/IP Indexing Servo Drive User Manual, publication 2097-UM001 Kinetix 2000 Multi-axis Servo Drive User Manual, publication 2093-UM001 Provides mounting, wiring, configuring, and troubleshooting information for these Kinetix motion control drive systems.