Installation Instructions (Cat. No. 1794-ASB Series B) &(, ), * &( -% ' # ,(*+ (&&-'# ,#(' * + , )-+" -,,(' ++ ((* ,( +/#, " + ' /#, " + ' "#' ++ ((* &(, % ('' ,(* ('' ,#('+ (&&(' ('' ,#('+ % 0 -+ ('' ,(* #+ ,* & *$ (! %% '2 * % 1 ( ' - %# ,#(' 2 (.
FLEX I/O Remote I/O Adapter If this product has the CE mark it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives.
FLEX I/O Remote I/O Adapter 3 1. Position the remote I/O adapter module A on a 35 x 7.5mm DIN rail B (A-B pt. no. 199-DR1; 46277-3; EN 50022) at a slight angle. 2. Hook the lip on the rear of the adapter (A) onto the top of the DIN rail (B), and rotate the adapter module onto the rail. 3. Press the adapter module down onto the DIN rail until flush. Locking tab (C) will snap into position and lock the adapter module to the DIN rail. 4.
FLEX I/O Remote I/O Adapter 1. Connect the remote I/O cable to the removable remote I/O connector. '-$ &+$ %&$'# &+$ '$ + &+$ 2. Connect +24V dc input to the left side of the lower connector, terminal E. 3. Connect 24V common to the left side of the upper connector, terminal D. 4.
FLEX I/O Remote I/O Adapter 5 1 2 1 2 3 3 4 4 5 6 7 5 6 7 8 8 The adapter switches are located under a flip-open cover on the front of the adapter. Set the switches as shown below.
FLEX I/O Remote I/O Adapter 1 2 3 4 5 6 7 8 $+,- +).* % .' + , +/ )& (*.-, ,- *- + *&0 & 0 1 2 3 4 5 6 7 8 6 )''.($ -$)( +) ,,)+ ,- +- ) %). )& ,- - - S1 S2 First I/O Group I/O Rack Number S1-8 S1-7 Module group ,- ( + -# S1-6 thru S1-1 ! + -) -# - & )( * " S2-8 S2-7 Hold Inputs S2-6 Last Adapter S2-5 Reply Delay , +/ )& (*.
FLEX I/O Remote I/O Adapter Rack Number 1747ĆSN PLC-2 & 1771ĆSN 7 S1 Switch Position 6 5 4 3 2 1
FLEX I/O Remote I/O Adapter Rack Number 1747ĆSN PLC-2 & 1771ĆSN PLC-5 S1 Switch Position PLC-5/250 PLC-3 6 5 4 3 2 1
FLEX I/O Remote I/O Adapter 9 1794ĆASB Specifications I/O Capacity 8 modules Power Supply Note: In order to comply with CE Low Voltage Directives, you must use a Safety Extra Low Voltage (SELV) or a Protected Extra Low Voltage (PELV) power supply to power this adapter. Input Voltage Rating 24V dc nominal Input Voltage Range 19.2V to 31.2V dc (includes 5% ac ripple) Communication Rate 57.6k bps 115.2k bps 230.
FLEX I/O Remote I/O Adapter Agency Certification (when product or packaging is marked) • CSA certified • CSA Class I, Division 2 Groups A, B, C, D certified • UL listed • CE marked for all applicable directives User Manual Publication 1794Ć6.5.3 1 Use this conductor category information for planning conductor routing. Refer to publication 1770Ć4.1, Industrial Automation Wiring and Grounding Guidelines." Publication 1794Ć5.
FLEX I/O Remote I/O Adapter 11 , , , , %*$) $ %" # $( %$( %' %&) %$ " #%*$) $ ! ) ' " *' ' " &&'%, # ) "- + '- ## * " ) %$ .
FLEX I/O Remote I/O Adapter '2& + (-0 -$$'!#1 5-0*"5'"# -0*" # "/3 02#01 **#,8 0 "*#7 -32& #!-," 20##2 '*5 3)## #* 8 6 8 3 *'! 2'-, 8 -4#+ #0 3.#01#"#1 .3 *'! 2'-, 8 #!#+ #0 3 *'! 2'-, 8 -4#+ #0 -.70'%&2 **#,8 0 "*#7 -+.
