Install Inst User Manual

ManualsBrandsRockwell Automation ManualsEquipment1793-OB16 Flex Integra Output Module

FLEX I/O and FLEX Integra are trademarks

of Rockwell Automation Publication 1793-5.9 - December 1999

Installation Instructions

FLEX Integra

16 Protected Source Output Module

(Cat. No. 1793-OB16P and -OB16PS)

Module Installation

This module mounts on a DIN rail. It connects to an adapter or another

FLEX I/O or Integra module. Note: If using this module with FLEX I/O

modules, do not mount between FLEX I/O modules. Mount Integra

modules to the right of the FLEX I/O modules. To mount this module:

1. Remove the cover plug (if used) in the male connector of the unit to

which you are connecting this module.

2. Position the module on the 35 x 7.5mm DIN rail A (A-B pt. no.

199-DR1).

3. Rotate the module onto the DIN rail with the top of the rail hooked

under the lip on the rear of the module.

30869-M

Summary of content (8 pages)

PAGE 1
Installation Instructions FLEX Integra 16 Protected Source Output Module (Cat. No. 1793-OB16P and -OB16PS) Module Installation This module mounts on a DIN rail. It connects to an adapter or another FLEX I/O or Integra module. Note: If using this module with FLEX I/O modules, do not mount between FLEX I/O modules. Mount Integra modules to the right of the FLEX I/O modules. To mount this module: 1. 2. 3.
PAGE 2
FLEX Integra 16 Protected Source Output Module 4. Press down to lock the module on the DIN rail. 30870-M 5. If the module does not lock in place, use a screwdriver of similar device to move the locking tab down, press the module flush with the DIN rail and release the locking tab to lock the module in place. Firmly push the module into the adjacent module/terminal base until the units lock together. 30871-M 6. 7. Repeat the above steps to install the next module.
PAGE 3
FLEX Integra 16 Protected Source Output Module ! 3 ATTENTION: Do not remove this module under power. Removing this module under power will break the electrical backplane (flexbus) connections.
PAGE 4
FLEX Integra 16 Protected Source Output Module Wiring This module is available with 2 styles of terminations: 1793-OB16P screw-cage and 1793-OB16PS - spring-clamp. Refer to the wiring figure below. 1793-OB16P COM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 COM A B V COM COM V 41817 1793-OB16PS COM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 COM A B V COM COM V 41815 Where: COM = common, V = +24V dc power, 0 thru 15 = outputs 1. 2. 3. 4. 5. 6.
PAGE 5
FLEX Integra 16 Protected Source Output Module 5 Wiring Connections Channel Output Common Channel Output 0 0 8 1 1 9 9 2 2 10 10 3 3 11 11 4 4 12 12 5 5 13 13 6 6 14 14 7 7 15 15 connect to corresponding terminal on row B Common 8 connect to corresponding terminal on row B +24V dc Power terminals V are internally connected together in the module. 24V dc common Common terminals COM are internally connected together in the module.
PAGE 6
FLEX Integra 16 Protected Source Output Module C-UL and UL Hazardous Location Approval Approbation d’utilisation dans des environnements dangereux par la C-UL and UL C-UL and UL certifies products for general use as well as for use in hazardous locations. Actual C-UL and UL certification is indicated by the product label as shown below, and not by statements in any user documentation.
PAGE 7
FLEX Integra 16 Protected Source Output Module C-UL and UL Hazardous Location Approval WARNING: Explosion Hazard • Substitution of components may impair suitability for Class I, Division 2. • Do not replace components unless power has been switched off or the area is known to be non-hazardous. • Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. • Do not disconnect connectors unless power has been switched off or the area is known to be non-hazardous.
PAGE 8
FLEX Integra 16 Protected Source Output Module Specifications - 16 Protected Output Module Cat. No. 1793-OB16P and -OB16PS Delay Time Off to On On to Off Flexbus Current 0.5ms maximum 1.0ms maximum 80mA maximum Power Dissipation 5W @ 31.2V dc Thermal Dissipation 17 BTU/hr @ 31.2V dc Indicators 16 yellow channel status indicators Fusing Outputs are electronically protected External dc Power Voltage Current 19.2-31.2V dc (5% ac ripple) 60mA Dimensions Inches (Millimeters) 2.72H x 3.7D x 2.