User guide

ManualsBrandsRockwell Automation ManualsEquipment1793-IB2XOB2PS FLEX INTEGRA 2 INPUT/2 PROTECTED OUTPUT MODUL

FLEX Integra and FLEX I/O are

trademarks of Rockwell Automation Publication 1793-5.3 - September 1999

Installation Instructions

FLEX Integra

2 Input/2 Protected Output Module

(Cat. No. 1793-IB2XOB2P and -IB2XOB2PS)

Module Installation

This module mounts on a DIN rail. It connects to an adapter or another

FLEX I/O or Integra module. Note: If using this module with FLEX I/O

modules, do not mount between FLEX I/O modules. Mount Integra

modules to the right of the FLEX I/O modules. To mount this module:

1. Remove the cover plug (if used) in the male connector of the unit to

which you are connecting this module.

2. Position the module on the 35 x 7.5mm DIN rail A (A-B pt. no.

199-DR1).

3. Rotate the module onto the DIN rail with the top of the rail hooked

under the lip on the rear of the module.

41355

30720-M

Summary of content (12 pages)

PAGE 1
Installation Instructions FLEX Integra 2 Input/2 Protected Output Module (Cat. No. 1793-IB2XOB2P and -IB2XOB2PS) 41355 Module Installation This module mounts on a DIN rail. It connects to an adapter or another FLEX I/O or Integra module. Note: If using this module with FLEX I/O modules, do not mount between FLEX I/O modules. Mount Integra modules to the right of the FLEX I/O modules. To mount this module: 1. 2. 3.
PAGE 2
FLEX Integra 2 Input/2 Protected Output Module 4. Press down to lock the module on the DIN rail. A 41377 5. If the module does not lock in place, use a screwdriver of similar device to move the locking tab down, press the module flush with the DIN rail and release the locking tab to lock the module in place. Firmly push the module into the adjacent module/terminal base until the units lock together. 41371 41370 6. 7. Repeat the above steps to install the next module.
PAGE 3
FLEX Integra 2 Input/2 Protected Output Module ! 3 ATTENTION: Do not remove this module under power. Removing this module under power will break the electrical backplane (flexbus) connections.
PAGE 4
FLEX Integra 2 Input/2 Protected Output Module Wiring This module is available with 2 styles of terminations; 1794-IB2XOB2P screw-cage and 1793-IB2XOB2PS - spring-clamp. Refer to the wiring figure below.
PAGE 5
FLEX Integra 2 Input/2 Protected Output Module 5 Wiring Channel Sink Input1 Input Terminal Supply Terminal 0 2 1 1 3 6 Source Output Output Terminal Common 0 4 12 1 5 13 +24V dc Terminals 1, 6, 8, 9, 14, 15 are internally connected together in the module. 24V dc common Terminals 0, 7, 10 thru 13 are internally connected together in the module 1 Two-wire devices use signal input and power terminals, 3-wire devices use signal input, supply and common terminals.
PAGE 6
FLEX Integra 2 Input/2 Protected Output Module Memory Mapping Bit/ Word 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 Read Reserved I1 I0 Write Reserved O1 O0 Write Reserved FT time Where: I = Input O = Output FT = Filter time Setting the Input Delay Time You can select the input delay time (DT) for input channels 00 and 01. Select the input delay time by setting the corresponding bits in the configuration word (word 3) for the module.
PAGE 7
FLEX Integra 2 Input/2 Protected Output Module CUL Hazardous Location Approval Approbation d’utilisation dans des environnements dangereux par la CUL CUL certifies products for general use as well as for use in hazardous locations. Actual CUL certification is indicated by the product label as shown below, and not by statements in any user documentation. La CUL certifie des produits pour une utilisation générale aussi bien que pour une utilisation en environnements dangereux.
PAGE 8
FLEX Integra 2 Input/2 Protected Output Module CUL Hazardous Location Approval $77(17,21 ([SORVLRQ +D]DUG • Substitution of components may impair suitability for Class I, Division 2. • Do not replace components unless power has been switched off or the area is known to be non-hazardous. • Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. • Do not disconnect connectors unless power has been switched off or the area is known to be non-hazardous.
PAGE 9
FLEX Integra 2 Input/2 Protected Output Module 9 Specifications - 2 Input/2 Protected Output Module Cat. No. 1793-IB2XOB2P and -IB2XOB2PS Module Type 2 input/2 output digital combination w/electronic fusing 1793-IB2XOB2P - screw-clamp terminations 1793-IB2XOB2PS - spring-clamp terminations Module Location DIN rail mounting Number of Channels 2 digital input - sinking/2 digital output - sourcing, protected Input On-state Voltage 10-31.
PAGE 10
FLEX Integra 2 Input/2 Protected Output Module Specifications - 2 Input/2 Protected Output Module Cat. No. 1793-IB2XOB2P and -IB2XOB2PS Dimensions in (mm) 2.72H x 3.15D x 2.
PAGE 11
FLEX Integra 2 Input/2 Protected Output Module 11 Publication 1793-5.
PAGE 12
Publication 1793-5.3 - September 1999 Supersedes Publication 1793-5.3 - September 1998 PN 955132-32A © (1999) Rockwell International Corporation.