Installation Instructions ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate (Cat. No. 1792D-CB23 and -KPLT) CB23 KPLT 43338 43333 The 23mm ArmorBlock MaXum Robot Ι/Ο Cable Base mates with 4 or 8 point modules, depending on your installation requirements, and optionally the Kempf box plate. No modification is required. Modules are interchangeable whether flat or round media cable bases are used. This interchangeability provides plug and play block upgrade capability and easy field replacement.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate These instructions describe the installation of the cable base. The catalog numbers for the cable base and Kempf box are: • 1792D-CB23 (for 23mm trunk or drop cable installation) • 1792D-KPLT (to mount the cable base on a Kempf box) IMPORTANT ArmorBlock MaXum modules and media cables are ordered and shipped separately.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 3 Throughout this publication, notes may be used to make you aware of safety considerations.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 meters without derating. This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR Publication 11.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 5 Install Your ArmorBlock Cable Base To install the cable base: • Mount the cable base • Attach the module to the base • Attach the cables These procedures are explained in detail in the following sections. Mount the Cable Base The cable base can be mounted either vertically or horizontally, using 3 screws. Cable bases accommodate 4 or 8 point ArmorBlock MaXum modules.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 1. Mount the MaXum Kempf plate to the Kempf box. MaXum Kempf plate MaXum Kempf box 43339 2. Mount the CB23 cable base to the gasket and the Kempf box. The mounting instructions are illustrated below.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 7 Attach the Module to the Base IMPORTANT Make sure you properly align the screws to complete the connections between the module contacts and the cable contacts. 1. Position the module over the mounted cable base. Align the three captive screws in the module with the accepting receptacles in the base. 2. Tighten the screws with a torque of 8 inch-pounds to secure the module to the base.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate ArmorBlock MaXum I/O modules are described in the following publications: • 1792D series of ArmorBlock MaXum Installation Instructions • 1792-TD001 ArmorBlock Technical Data The DeviceNet Network uses advanced network technology, producer/consumer communication, to increase network functionality and throughput. Visit our web site at http://www.ab.com/networks for producer/consumer technology information and updates. Attach the Cables 1.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 9 3. Attach your I/O connector cables. Female Male Network Out Network In 31463-m WARNING ! If you connect or disconnect the DeviceNet cable with power applied to this module or any device on the network, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate WARNING ! WARNING ! Use supply wires suitable for 30°C above surrounding ambient. If you connect or disconnect wiring while the field-side power is on, an electrical arc can occur. This can cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.
1 4 14 5 17 12 16 6 8 7 Assembly side 2 Incoming installation remote bus (Female connector) 4 +24V (US1) RET (US1) +24V (US2) 5 15 16 reserved Flange 13 14 12 17 3 2 PE reserved DeviceNet Low CCR2 DeviceNet High CCR1 RET (US2) 11 6 COM (Profi A) reserved (Profi B) 1 7 8 9 10 DO ~DO SCM1 (DI) SCM2 (~DI) Incoming Hybrid Cable Blue Green/Yellow Red White Brown Blue Blue Black Green Red Red Gray Pink Yellow Green DO CCR1 RET (US2) +24V (US1) RET (US1) +24V (US2) COM reserv
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate Specifications Robot I/O Cable Bases - Cat. No. 1792D-CB23 & -KPLT General Specifications For general specifications, see the ArmorBlock MaXum module’s documentation or the Technical Data, publication number 1792-TD001. The specifications listed in these publications are for the assembled module and cable base.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 13 Hazardous Location Approval The following information applies when operating this equipment in hazardous locations: Informations sur l’utilisation de cet équipement en environnements dangereux : Products marked “CL I, DIV 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate This product has been tested at an Open DeviceNet Vendor Association, Inc. (ODVA) authorized independent test laboratory and found to comply with ODVA Conformance Test. Please contact the ODVA website (http://www.odva.org) for listing of products tested by ODVA independent test labs for further details.
ArmorBlock MaXum Robot I/O Cable Base and Kempf Box Plate 15 Notes: Publication 1792D-IN054B-EN-P - April 2003
Rockwell Automation Support Rockwell Automation tests all of our products to ensure that they are fully operational when shipped from the manufacturing facility. If you are experiencing installation or startup problems, please review the troubleshooting information contained in this publication first. If you need technical assistance to get your module up and running, please contact Customer Support (see the table below); our trained technical specialists are available to help.
