Installation Instructions ArmorBlock MaXum I/O Cable Bases Series B (Cat. No. 1792D-CB18, -CB18P, -CB18PT) CB18 41712 CB18P 41713 CB18PT 41714 The 18mm ArmorBlock MaXum™ Ι/Ο Cable Bases mate with 4 or 8 point modules depending on your installation requirements. No modification is required. Modules are interchangeable whether flat or round media cable bases are used. This interchangeability provides plug and play block upgrade capability and easy field replacement.
ArmorBlock MaXum I/O Cable Bases Series B These instructions describe the installation of each cable base. The catalog numbers for the cable bases are: • 1792D-CB18 for 18mm trunk or drop cable installation • 1792D-CB18P, -CB18PT for 18mm trunk or drop cable installation when an auxiliary output power connection is necessary IMPORTANT ArmorBlock MaXum modules and media cables are ordered and shipped separately.
ArmorBlock MaXum I/O Cable Bases Series B 3 Mount the Cable Base The cable base can be mounted either vertically or horizontally, using 3 screws. Cable bases accommodate 4 or 8 point ArmorBlock MaXum modules. You must allow additional space for installation of 8 point ArmorBlock MaXum modules. They are longer than the 4 point modules. 1792D-CB18 1.90in 48.18mm 0.26in 6.5mm When installing a cable base with an 8 connector module, allow for the additional length. 2.70in 68.5mm 0.64in 16.25mm 1.
ArmorBlock MaXum I/O Cable Bases Series B 1.90in 48.18mm 1792D-CB18P 0.26in 6.5mm When installing a cable base with an 8 connector module, allow for the additional length. 2.70in 68.5mm 1.42in 36mm 4.21in 107mm 0.64in 16.25mm 8.23in 209mm 8 connector module 6.10in 155mm 4 connector module 1.63in 41.5mm .764in 19.4mm 1.35in 34.25mm 4.00in 101.5mm .791in 20.1mm 2.130in 54.1mm 41696 2.70in 68.5mm 1792D-CB18PT 1.34in 34mm 1.42in 36mm 1.
ArmorBlock MaXum I/O Cable Bases Series B 5 Attach the Module IMPORTANT Make sure you properly align the screws to complete the connections between the module contacts and the cable contacts. 1. Position the module over the mounted cable base. Align the three captive screws in the module with the accepting receptacles in the base. 2. Tighten the screws with a torque of 8 inch-pounds to secure the module to the base. Screws must be aligned properly to complete contact connections.
ArmorBlock MaXum I/O Cable Bases Series B Attach the Cables 1. Attach your network cable and power cable (if used) to the connectors. 2. Cover the power connector with a cap if it is not used. 3. Attach your point connector cables.
ArmorBlock MaXum I/O Cable Bases Series B 7 Use the graphics below to connect DeviceNet cable to your module.
ArmorBlock MaXum I/O Cable Bases Series B Hazardous Location Approval The following information applies only to products marked with Hazardous Location Approval, when operating in hazardous locations: Products marked “CL I, DIV 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code.
ArmorBlock MaXum I/O Cable Bases Series B WARNING ! 9 When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method that complies with the governing electrical codes.
ArmorBlock MaXum I/O Cable Bases Series B AVERTISSEMENT ! AVERTISSEMENT ! Utiliser des fils d’alimentation qui conviennent à une température de 30°C au-dessus de la température ambiante. Pour une utilisation en environnement de classe i, division 2 dangereux, cet equipement doit etre monte dans un boitier avec un cablage approprie conforme aux normes electriques en vigueur.
ArmorBlock MaXum I/O Cable Bases Series B 11 This product has been tested at an Open DeviceNet Vendor Association, Inc. (ODVA) authorized independent test laboratory and found to comply with ODVA Conformance Test. Please contact the ODVA website (http://www.odva.org) for listing of products tested by ODVA independent test labs for further details.
ArmorBlock and ArmorBlock MaXum are trademarks of Rockwell Automation. DeviceNet is a trademark of Open DeviceNet Vendor Association (ODVA). Publication 1792D-IN036B-EN-P - September 2000 Supersedes Publication 1792D-5.36 - April 1999 PN 957395-96 © 2000 Rockwell International Corporation.
