Owner manual

ManualsBrandsRockwell Automation ManualsEquipment1792D-4B0LP INSTL INSTR ARMORBLOCK INPUT

Installation Instructions

Publication 1792D-5.27- January 1999

ArmorBlock LP2 4 Sinking Input Module

(Cat. No. 1792D-4B0LP)

This ArmorBlock LP2 I/O module (Cat. No. 1792D-4B0LP) is a stand-

alone 24V dc I/O product which communicates via a DeviceNet network.

The sealed housing of this module requires no enclosure.

This model has 4 sinking inputs.

Package Contents

Your package contains:

• 1 ArmorBlock LP2 Module

• Installation Instructions

Network Status

Module Status

41621

Summary of content (8 pages)

PAGE 1
Installation Instructions ArmorBlock LP2 4 Sinking Input Module (Cat. No. 1792D-4B0LP) I0 I3 I1 I2 Network Status Module Status 41621 This ArmorBlock LP2 I/O module (Cat. No. 1792D-4B0LP) is a standalone 24V dc I/O product which communicates via a DeviceNet network. The sealed housing of this module requires no enclosure. This model has 4 sinking inputs. Package Contents Your package contains: • 1 ArmorBlock LP2 Module • Installation Instructions . Publication 1792D-5.
PAGE 2
ArmorBlock LP2 4 Sinking Input Module European Union Directive Compliance If this product has the CE mark it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives.
PAGE 3
ArmorBlock LP2 4 Sinking Input Module 3 Install the Module 1. Attach the module using the dimensions shown below. 1.95 in 49.5mm 12in 305mm I0 I3 I1 I2 Network Status 4.21 in 107mm Module Status 0.25 in 6.25mm 1.02 in 26.0mm 2. Connect the grey DeviceNet cable to the DeviceNet trunk. Use the 1485P-P1R5-MN5R1 T-Part tap to make the connection to round media. Use the 1485P-P1E4-R5 to connect to the Kwik Link flat media system.
PAGE 4
ArmorBlock LP2 4 Sinking Input Module ATTENTION: ! • Make sure to connect the proper color coded cables together. DeviceNet cables should connect with DeviceNet cables. • Make sure all connectors and caps are securely tightened to properly seal the connections against leaks and maintain IP67 requirements • For maximum noise immunity, input and output cable return wires must be properly terminated. When inputs and outputs are connected in loopback, return wires should be connected together.
PAGE 5
ArmorBlock LP2 4 Sinking Input Module 5 Communicate With Your ArmorBlock LP2 Module This ArmorBlock module’s I/O is exchanged with the master through a poll, change of state, or cyclic connection. The module produces input data as follows: Type of I/O Connections Consumes Produces Cyclic 0 Byte 1 Byte Polled 0 Byte 1 Byte Change of State 0 Byte 1 Byte Cyclic - allows configuration of the block as an I/O client. The block will produce its I/O cyclically at the rate configured.
PAGE 6
ArmorBlock LP2 4 Sinking Input Module Troubleshoot with the Indicators This module has the following indicators: • Network status indicator • Module status indicator • Individual point status indicators for inputs 0, 1, 2, and 3 Point indicator for input 0 Connector A I0 I3 Point indicator for input 3 Connector D Point indicator for input 1 Connector B I1 I2 Point indicator for input 2 Connector C DeviceNet Indicators Network Status Module Status LED Assignments Module Status Indicator Indi
PAGE 7
ArmorBlock LP2 4 Sinking Input Module Red Blink Solid Connection Timed Out Failed Communication: A duplicate node address exists or module is at the wrong baud rate. I/O Status Indicators Function Module Status Indicator Point Indicator Condition Inputs Green Green None Yellow No valid input Valid input For more information on indications see the Product Data publication 1792-2.1. Specifications 4 Input Module - Cat. No.
PAGE 8
ArmorBlock LP2 4 Sinking Input Module 4 Input Module - Cat. No. 1792D-4B0LP Sinking Input Specifications Environmental Conditions Operational Temperature Storage Temperature Relative Humidity Shock Operating Non-operating Vibration Conductors Max Min -25 to 60o (-13 to 140oF) -25 to 80oC (-13 to 176OF) Up to 100% 30g peak acceleration, 11 (+1) ms pulse width 50g peak acceleration, 11(+1)ms pulse width Tested 10g @ 10-500Hz per IEC 68-2-6 Publication DN-6.7.