Owner's manual

ManualsBrandsRockwell Automation ManualsEquipment1792-IB8XOB8PLP INSTL INSTR ARMORBLOCK LP 8/8

Packing Data

Publication 1792-5.8 – December 1997

DeviceNet

is a trademark of Open DeviceNet V

endor Association, Inc.

DeviceNetManager is a trademark of Rockwell Automation





(Catalog Number 1792-IB8XOB8PLP)

This 1792 ArmorBlock I/O block module (Cat. No.

1792-IB8XOB8PLP)

contains I/O circuits, a built-in power supply, and a

built-in DeviceNet I/O adapter. Because of its sealed housing, this 1792

I/O block requires no enclosure. It is compatible with PLC or SLC

programmable controllers using DeviceNet scanners. The I/O values are

accessible from the PLC or SLC programmable controller data table.

This ArmorBlock-LP module has no switches to set. You set module

parameters using the DeviceNet Manager Software (cat. no. 1787-MGR)

or similar configuration tool.

Contents

This box contains:

• 1 ArmorBlock–LP module

• Package containing 10 write-on indicator tabs, and 7 micro caps

• 1 DeviceNet right hand aluminum T-port tap (part number 97042401)

• Installation Instructions

Installation Instruction

Summary of content (12 pages)

PAGE 1
Packing Data PK Installation Instructions (Catalog Number 1792-IB8XOB8PLP) This 1792 ArmorBlock I/O block module (Cat. No. 1792-IB8XOB8PLP) contains I/O circuits, a built-in power supply, and a built-in DeviceNet I/O adapter. Because of its sealed housing, this 1792 I/O block requires no enclosure. It is compatible with PLC or SLC programmable controllers using DeviceNet scanners. The I/O values are accessible from the PLC or SLC programmable controller data table.
PAGE 2
ArmorBlock-LP 8 Input/8 Output Module European Union Directive Compliance If this product is installed within the European Union or EEA regions and has the CE mark, the following regulations apply. EMC Directive This apparatus is tested to meet Council Directive 89/336/EEC Electromagnetic Compatibility (EMC). The product described in this manual is intended for use in an industrial environment.
PAGE 3
ArmorBlock-LP 8 Input/8 Output Module 3 Set the Node Address Each ArmorBlock-LP comes with its internal program set for node address 63 and a communication rate of 125K bps.
PAGE 4
ArmorBlock-LP 8 Input/8 Output Module Mounting Dimensions 2.0 (51) 0.8 (20.1) A B A B 4 B A B A 1.1 (27) inches (millimeters 1.1 (27) 6.8 (172.1) 1.3 1.5 (33) (39) 1 3 B B 5 A A B B 7 A A 2.4 1.4 (60) (36) 0.18 (4.5) 2 4.2 (107) 6 0.63 (16) 8 1.8 1.5 (45) (38) 1.1 (27) 6.0 (152) 1.25 (32) 1.0 (25.
PAGE 5
ArmorBlock-LP 8 Input/8 Output Module 5 Seven micro caps are included with your module. Use these caps to cover and seal unused ports. Pinout diagrams for the connectors are shown below. ATTENTION: Make sure all connectors are securely tightened to properly seal the connections against leaks and maintain IP67 requirements. ! Connecting the Input Wiring Connect input wiring to the micro-connectors which screw into mating connectors on the front of the block.
PAGE 6
ArmorBlock-LP 8 Input/8 Output Module Connecting the Output Power Wiring Connect output power wiring to the 3-pin mini-connector on the end of the block. Important: The outputs use electronic overcurrent fault protection. Make certain your output power supply can handle overcurrent events.
PAGE 7
ArmorBlock-LP 8 Input/8 Output Module Type of I/O Connections Consumes 7 Produces Polled 1 Bytes 2 Bytes Bit Strobe 0 Bytes 2 Bytes Change of State 0 Bytes 2 Bytes Polled device – a master initiates communication by sending its polled I/O message to the ArmorBlock module. The 8 input/8 output module consumes the message, updates outputs, and produces a response that reflects the status of 1) its inputs, and 2) any input or output faults.
PAGE 8
ArmorBlock-LP 8 Input/8 Output Module Word Bit Description Produces 00–07 Input Status bits – when the bit is set (1), the input is on. Bit 00 corresponds to input 1A, bit 01 corresponds to input 3A, bit 02 to input 5A, bit 03 input 7A. Bit 04 corresponds to input 1B, bit 05 to input 3B, bit 06 to input 5B, and bit 07 to input 7B. Produces 00–05 Reserved Consumes 06 OF = output fault status bit – indicates presence of field power (default).
PAGE 9
ArmorBlock-LP 8 Input/8 Output Module OVL = Sensor and Output Status Indicator 2 4 B A B A B A A B B A A B B B US = Output Power Supply Status Indicator 1 3 5 7 IN A A OUT 8 6 NS = Network Status Indicator Output Connector 9 MS = Module Status Indicator UL = Module Power Supply Status Indicator A and B = Input and Output I/O Status Indicators 30197–M Note: This module contains a circuit to protect the DeviceNet power supply from short circuits in an attached sensor or sensor cabl
PAGE 10
ArmorBlock-LP 8 Input/8 Output Module Sensor Short Circuit Indicator OVL Indication OFF Solid Red Status Sensor source voltage operating correctly 1 or more Sensor source voltage shorts, output overload or no load condition Output I/O Status Indicators A and B Indication OFF Yellow Status Output is off Output is on Input I/O Status Indicators A and B Indication OFF Yellow Status No valid input signal present Valid input signal present Module and Sensor Power Supply Status Indicators US and UL Ind
PAGE 11
ArmorBlock-LP 8 Input/8 Output Module Sensor Source Voltage Current 11 Minimum 13V dc @ 400mA out and DeviceNet power = 15V dc 50mA per point, 0.4A total per module Output Specifications Output Power Supply Note: In order to comply with CE Low Voltage Directives, you must use a Safety Extra Low Voltage (SELV) or a Protected Extra Low Voltage (PELV) power supply to power the outputs of this module.
PAGE 12
ArmorBlock-LP 8 Input/8 Output Module General Specifications Dimensions Inches Millimeters Environmental Conditions Operational Temperature Storage Temperature Relative Humidity Shock Operating Non-operating Vibration 6.8H X 2.4W X 2.0D 172.1H X 60W X 51D 0 to 60oC (32 to 140oF) –20 to 80oC (–40 to 176oF) up to 100% 30 g peak acceleration, 11(+1)ms pulse width 50 g peak acceleration, 11(+1)ms pulse width Tested 10 g @ 10–500Hz per IEC 68-2-6 Conductors Refer to publication 1485-6.7.