User Manual

i Publication 1790-UM001A-EN-P - March 2002
Table of Contents
Chapter 1
Overview
How to Use Analog I/O . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
General Diagnostic Features . . . . . . . . . . . . . . . . . . . . . 1-4
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Chapter 2
Installation and Wiring
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Prevent Electrostatic Discharge . . . . . . . . . . . . . . . . . . . 2-2
Environmnet and Enclosure . . . . . . . . . . . . . . . . . . . . . 2-2
Remove Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
General Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Reducing Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Protecting the Circuit Board from Contamination. . . . . . 2-3
Installing CompactBlock LDX I/O . . . . . . . . . . . . . . . . . . . 2-4
Set the Node Address on the Base Block . . . . . . . . . . . 2-4
Mount the Base Block . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Mount the Optional Expansion Blocks . . . . . . . . . . . . . 2-6
Connect the DeviceNet Cable . . . . . . . . . . . . . . . . . . . . 2-7
I/O System Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . 2-8
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Output Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Effect of Transducer/Sensor and Cable Length
Impedance on Voltage Input Accuracy . . . . . . . . . . . . . 2-9
Effect of Device and Cable Output Impedance
on Output Module Accuracy. . . . . . . . . . . . . . . . . . . . . 2-11
Wiring the Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
1790D-N4C0, 1790D-N4V0 Analog 4 Input Base D-Shell
Modules Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
1790D-TN4C0, 1790D-TN4V0 Analog 4 Input Base Modules
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
1790D-N0C2, 1790D-N0V2 Analog 2 Output Base D-Shell
Modules Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
1790D-TN0C2, 1790D-TN0V2 Analog 4 Input Base Modules
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18