User Manual

ManualsBrandsRockwell Automation ManualsEquipment1788-ENBT EtherNet/IP Daughtercard Installation Instructions

Publication 1788-IN054A-EN-P - September 2002

Installation Instructions

EtherNet/IP Daughtercard

Catalog Number 1788-ENBT

Use this document as a guide to install the EtherNet/IP daughtercard. This

document covers only the hardware installation; refer to the Flex Logix System User

Manual, publication 1794-UM001, for information about configuring the

daughtercard.

This table lists the contents of the document and where to find specific information.

For information abou t See page

Important User Information 2

About the EtherNet/IP Daughtercard 4

Required Software 4

Related Publications 4

Identifying Daughtercard Components 4

Install the Daughtercard 5

Connect the Daughtercard to the Network 5

Apply Host Power 6

Daughtercard System Performance 6

Interpret the LED Status Indicators 7

Where to Find Information on Configuring the Daughtercard 9

Hazardous Location Information 10

Specifications 11

Summary of content (12 pages)

PAGE 1
Installation Instructions EtherNet/IP Daughtercard Catalog Number 1788-ENBT Use this document as a guide to install the EtherNet/IP daughtercard. This document covers only the hardware installation; refer to the FlexLogix System User Manual, publication 1794-UM001, for information about configuring the daughtercard. This table lists the contents of the document and where to find specific information.
PAGE 2
EtherNet/IP Daughtercard Important User Information Because of the variety of uses for the products described in this publication, those responsible for the application and use of these products must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards. In no event will Rockwell Automation, Inc.
PAGE 3
EtherNet/IP Daughtercard ATTENTION ! 3 Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 meters without derating. This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR Publication 11.
PAGE 4
EtherNet/IP Daughtercard About the EtherNet/IP Daughtercard 31447-M The network daughtercard architecture defines a common hardware and software interface that several different network interface cards will support. This lets products that have been designed to support the network daughtercard option support several different Rockwell Automation networks. You can install the 1788-ENBT EtherNet/IP daughtercard in any host device that supports the daughtercard.
PAGE 5
EtherNet/IP Daughtercard 5 Install the Daughtercard Due to wide variation in available host devices, we cannot provide specific installation instructions in this document. For instructions on how to install the daughtercard in a host device, refer to the user manual for the particular host device. IMPORTANT WARNING Do not insert or remove the daughtercard while the host is under power. The daughtercard is not designed to be inserted or removed while the host is powered.
PAGE 6
EtherNet/IP Daughtercard 1. Use an RJ45 connector to connect to the EtherNet/IP network. Wire the connector according to this illustration: 8 ------ NC 7 ------ NC 6 ------ RD5 ------ NC 4 ------ NC 3 ------ RD+ 2 ------ TD1 ------ TD+ 2. Attach the connector to the EtherNet/IP port on the daughtercard. IMPORTANT We recommend connecting the module to the network via a 100MB Ethernet switch, which will reduce collisions and lost packets and increase network bandwidth.
PAGE 7
EtherNet/IP Daughtercard 7 Interpret the LED Status Indicators The four status indicators on the daughtercard provide information about the network, the daughtercard, and its connections. The following tables outline the possible states, explain what each state means, and indicate what action you should take, if any, to correct that state. Module Status (MS) Indicator This LED indicates whether or not the daughtercard has power and is operating properly.
PAGE 8
EtherNet/IP Daughtercard Network Status (NS) Indicator This LED indicates whether or not the daughtercard has an IP address and whether or not connections are established. Condition Status Indicates Recommended Action off not initialized The daughtercard does not have an IP address and is operating in BOOTP mode. Verify that the BOOTP server is running. flashing green no CIP connections established The daughtercard has an IP address, but no CIP connections are established.
PAGE 9
EtherNet/IP Daughtercard 9 Utilization Percent (U%) Indicator This LED indicates utilization percent of the daughtercard only and does not address the system performance of the daughtercard plus host. Condition Status Indicates Recommended Action off less than 80% utilization The I/O packet rate to/from this daughtercard is less than 80% of the available packet rate and less than 80% of the 32 available I/O connections are currently in use. Normal operation. No action required.
PAGE 10
EtherNet/IP Daughtercard Hazardous Location Information The following information applies when operating this equipment in hazardous locations: Informations sur l’utilisation de cet équipement en environnements dangereux : Products marked “CL I, DIV 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code.
PAGE 11
EtherNet/IP Daughtercard 11 Specifications Characteristic Value Power Requirements 5V dc @ 465mA(1) Power Consumption 5 V dc, 2.33W Thermal Dissipation 8.0 BTU/hr Isolation Voltage Tested to withstand 500V ac for 60 seconds Ethernet Conductors Wiring 802.
PAGE 12
Vibration IEC60068-2-6 (Test Fc, Operating): 5g @ 10-500Hz Weight 0.1 kg (0.2 lb.) Certifications: (when product is marked) c-UR-us (1) (2) (3) UL Recognized Component Industrial Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for US and Canada. European Union 89/336/EEC EMC Directive, compliant with: CE(3) EN 61000-6-4; Industrial Emissions EN 50082-2; Industrial Immunity EN 61326; Meas./Control/Lab.