Manual

ManualsBrandsRockwell Automation ManualsEquipment1785-M100_ME16_ME32_ME64 INSTL DATA ENHANCED ETHERNET PLC-5

Enhanced PLC5 and Ethernet PLC5

Programmable Controller

Memory Module

(Cat. No. 1785-ME16, -ME32, -ME64, and -M100)

Installation Data

This document provides you with the following information.

For information about: Go to page:

European Union directive compliance 2

choosing compatible processors and software for the memory module 3

handling the memory module 3

setting backplane switches 4

installing the memory module 5

removing the memory module 5

using the write protection jumper 5

writing to the memory module 6

handling an error while writing to the memory module 8

restoring a program from a memory module 8

specifications 9

These processors are referred to as enhanced PLC-5

programmable controllers:

PLC-5/11

PLC-5/20

PLC-5/30

PLC-5/40, -5/40L

PLC-5/60, -5/60L

PLC-5/80

These processors are referred to as Ethernet PLC-5

programmable controllers:

PLC-5/20E

PLC-5/40E

PLC-5/80E

To the Installer

Terminology

Summary of content (10 pages)

PAGE 1
Enhanced PLC 5 and Ethernet PLC 5 Programmable Controller Memory Module (Cat. No. 1785-ME16, -ME32, -ME64, and -M100) Installation Data To the Installer This document provides you with the following information.
PAGE 2
Installation Installation DataData PLC 5/11, 5/20, 5/40, Enhanced PLC 5 and 5/30, Ethernet PLC 5 5/40L, 5/60 Programmable Controller Memory Programmable Controller Memory Module Module European Union Directive Compliance If this product is installed within the European Union or EEA regions and the product has a CE mark, the following regulations apply.
PAGE 3
Installation Data Enhanced PLC 5 and Ethernet PLC 5 Programmable Controller Memory Module Choosing Compatible Processors and Software for the Memory Module Table 1 shows the the programmable controllers and the software that are compatible with the 1785-ME16, -ME32, -ME64, -M100 memory modules.
PAGE 4
Installation Installation DataData PLC 5/11, 5/20, 5/40, Enhanced PLC 5 and 5/30, Ethernet PLC 5 5/40L, 5/60 Programmable Controller Memory Programmable Controller Memory Module Module Setting Backplane Switches Set the I/O chassis backplane switches before you install the PLC-5 processor. Use a ballpoint pen to set each switch (do not use a pencil because the tip can break off and short the switch).
PAGE 5
Installation Data Enhanced PLC 5 and Ethernet PLC 5 Programmable Controller Memory Module Installing the Memory Module Insert the memory module into the front of the PLC-5 processor by following these steps: 1. Turn off power to the I/O chassis and processor. ATTENTION: Do not insert or remove the memory module under power. Insertion or removal under power can result in loss of program memory and a processor fault. 2.
PAGE 6
Installation Installation DataData PLC 5/11, 5/20, 5/40, Enhanced PLC 5 and 5/30, Ethernet PLC 5 5/40L, 5/60 Programmable Controller Memory Programmable Controller Memory Module Module Writing to the Memory Module Use the following steps to store a program on your memory module. Important: If you are using a 1785-L40B series A, revision B or a 1785-L60B series A, revision B processor, you must have the Global Status Flag file set to zero.
PAGE 7
Installation Data Enhanced PLC 5 and Ethernet PLC 5 Programmable Controller Memory Module 7. Ladder Editor Main Menu Transfer a duplicate of your program to the memory module. You must be programming online to write to a memory module (use the figure below). | I:001 O:005 | +––]/[––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––( )––+ | 14 10 | | +TON–––––––––––––––+ | +––––––––––––––––––––––––––––––––––––––––––––––––––+TIMER ON DELAY +–(EN)–+ | |Timer T4:0| | | |Time base 0.
PAGE 8
Installation Installation DataData PLC 5/11, 5/20, 5/40, Enhanced PLC 5 and 5/30, Ethernet PLC 5 5/40L, 5/60 Programmable Controller Memory Programmable Controller Memory Module Module Handling an Error while Writing to the Memory Module If an error occurs during a write to the memory module, you see this message displayed: EEPROM NOT BURNED If you get this message, do the following: check that you inserted the write protect jumper check minor fault bit (S:10/8) in the status file.
PAGE 9
Installation Data Enhanced PLC 5 and Ethernet PLC 5 Programmable Controller Memory Module Important: You can have continuous processor memory backup after restoring a program from a memory module to a processor by following these instructions: Locking Bar Ejector Tab PLC 5 processor Card Guides Specifications 1. Turn off power to the processor and I/O chassis. 2. Remove the memory module by following the removal procedure in this document (see page 5). 3.
PAGE 10
Installation Installation DataData PLC 5/11, 5/20, 5/40, Enhanced PLC 5 and 5/30, Ethernet PLC 5 5/40L, 5/60 Programmable Controller Memory Programmable Controller Memory Module Module Allen Bradley, a Rockwell Automation Business, has been helping its customers improve productivity and quality for more than 90 years. We design, manufacture and support a broad range of automation products worldwide.