User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover
1–39Abbreviated Command and Status Blocks
Publication
1771-6.5.88 – July 1997
Word Pro-Set Address Description
Bit-mapped Status Words
EPS01 B34:0 Block ID 00000111 (lower byte)
EPS01 B34:0 Jog status (upper byte)
EPS02 B34:1 Status of profile execution
EPS03 B34:2 Miscellaneous status
EPS04 B34:3 Status of watchdog timers
EPS05-06 B39:12-13 RFU
EPS07 B39:14 CV high limit alarms
EPS08 B39:15 CV low limit alarms
Actuals from Ejector Profile for Full Advance
EPS09 N45:181 Segment 1 velocity
EPS10 N45:182 Segment 1 pressure
EPS11 N45:183 Segment 1 execution time
EPS12 N45:184 Segment 2 velocity
EPS13 N45:185 Segment 2 pressure
EPS14 N45:186 Segment 2 execution time
EPS15 N45:187 Segment 3 velocity
EPS16 N45:188 Segment 3 pressure
EPS17 N45:189 Segment 3 execution time
EPS18-20 N45:190-192 RFU
Actuals from Ejector Profile for Tip Retract
EPS21 N45:193 Tip retract velocity
EPS22 N45:194 Tip retract pressure
EPS23 N45:195 Tip retract execution time
EPS24-26 N45:196-198 RFU
Actuals from Ejector Profile for Tip Advance
EPS27 N45:199 Tip advance velocity
EPS28 N45:200 Tip advance pressure
EPS29 N45:201 Tip advance execution time
EPS30-32 N45:202-204 RFU
Actuals from Ejector Profile for Full Retract
EPS33 N45:205 Segment 1 velocity
EPS34 N45:206 Segment 1 pressure
EPS35 N45:207 Segment 1 execution time
EPS36 N45:208 Segment 2 velocity
EPS37 N45:209 Segment 2 pressure
EPS38 N45:210 Segment 2 execution time
EPS39 N45:211 Segment 3 velocity
EPS40 N45:212 Segment 3 pressure
EPS41 N45:213 Segment 3 execution time
EPS42-52 N45:214-224 RFU
Maximum Pressure During Ejector Profile
EPS53 N45:225 Ejector pressure
EPS54-56 N45:226-228 RFU
Profile Execution Time
EPS57 N45:229 Ejector profile
EPS58-64 N45:230-236 RFU
EPS – Ejector Profile
Status Block