User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover
1–23Abbreviated Command and Status Blocks
Publication
1771-6.5.88 – July 1997
End of Profile Set-output Values
OSC33
N43:509 Output #1
OSC34 N43:510 Output #2
OSC35 N43:511 Output #3
OSC36 N43:512 Output #4
OSC37 N43:513 Output #5
OSC38 N43:514 Output #6
OSC39 N43:515 Output #7
OSC40 N43:516 Output #8
Pressure Control Limits
OSC41 N43:517 Minimum limit
OSC42 N43:518 Maximum limit
OSC43 N43:519 % output for minimum
OSC44 N43:520 % output for maximum
Velocity Control Limits
OSC45 N43:521 Minimum limit
OSC46 N43:522 Maximum limit
OSC47 N43:523 % output for minimum
OSC48 N43:524 % output for maximum
Profile Tuning Constants
OSC49 N43:525 Proportional gain, pressure control
OSC50 N43:526 Integral gain, pressure control
OSC51 N43:527 Derivative gain, pressure control
OSC52 N43:528 Proportional gain, velocity control
OSC53 N43:529 Feedforward gain, velocity control
OSC54-56 N43:530-532 RFU
Setpoint for Profile Pressure Alarm
OSC57 N43:533 High pressure alarm
OSC58-64 N43:534-540 RFU
Word Pro-Set Address Description
Bit-mapped Control Words
PKC01 B38:8 Block ID 00000000 00001010
PKC02 B38:9 Selected valve configurations
PKC03-04 B38:10-11 RFU
Expert Response Compensation Percentage
PKC05 N44:121 ERC % minimum cavity pressure
PKC06 N44:122 ERC % minimum ram pressure
PKC07-08 N44:123-124 RFU
Set-output Values for Unselected Valves (During Profile)
PKC09 N44:125 Output #1
PKC10 N44:126 Output #2
PKC11 N44:127 Output #3
PKC12 N44:128 Output #4
PKC13 N44:129 Output #5
PKC14 N44:130 Output #6
PKC15 N44:131 Output #7
PKC16 N44:132 Output #8
PKC – Pack
Configuration Block