User Manual

Table of Contents ii
SOC – Second Clamp Open Configuration Block 1–32 . . . . . . . . .
TCC
– Third Clamp Close Configuration Block 1–33 . . . . . . . . . . .
TOC
– Third Clamp Open Configuration Block 1–35 . . . . . . . . . . .
CLS – Clamp and Eject ERC Values Status Block
1–36 . . . . . . . .
CPS – Clamp Close Profiles Status Block
1–37 . . . . . . . . . . . . . .
EPS
– Ejector Profile Status Block 1–39 . . . . . . . . . . . . . . . . . . .
HPS – Pack/Hold Profile Status Block
1–40 . . . . . . . . . . . . . . . . .
IPS
– Injection Profile Status Block 1–41 . . . . . . . . . . . . . . . . . . .
OPS – Clamp Open Profiles Status Block
1–42 . . . . . . . . . . . . . .
PPS
– Plastication Profile Status Block 1–44 . . . . . . . . . . . . . . . .
PTS – Process Trace Status Block
1–45 . . . . . . . . . . . . . . . . . . .
RLS – Inject ERC Values Status Block
1–46 . . . . . . . . . . . . . . . . .
SYS - System Status Block
1–47 . . . . . . . . . . . . . . . . . . . . . . . .
Command Word/Bit Descriptions 2–1. . . . . . . . . . . . . . . .
Alphabetical List of Command Blocks and Block ID Codes 2–1 . .
List
of Data W ords 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block ID Word
2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Words
2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stored-value Words 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open Words
2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reserved Words
2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engineering Units
2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data
Blocks Require I/O Configuration 2–3 . . . . . . . . . . . . . . . . .
Data Blocks for System Control
2–4 . . . . . . . . . . . . . . . . . . . . .
Data Blocks for Controlling Ram (Screw) Position
2–4 . . . . . . . . .
Data
Blocks for Controlling Clamp Position 2–5 . . . . . . . . . . . . .
Data
Blocks for Controlling Ejector Position 2–5 . . . . . . . . . . . . .
Sensors
Required 2–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLC – Clamp and Eject ERC Values Block
2–7 . . . . . . . . . . . . .
Bit-mapped
Control W ords 2–7 . . . . . . . . . . . . . . . . . . . . . . .
Clamp Close Profiles ERC Values
2–7 . . . . . . . . . . . . . . . . . .
Clamp Open Profiles ERC Values 2–7 . . . . . . . . . . . . . . . . . .
Ejector
Profile ERC V alues 2–7 . . . . . . . . . . . . . . . . . . . . . . .
CPC – Clamp Close Profile Block
2–8 . . . . . . . . . . . . . . . . . . . .
Bit-mapped
Control W ords 2–8 . . . . . . . . . . . . . . . . . . . . . . .
First Clamp Close Profile Setpoints 2–10 . . . . . . . . . . . . . . . . .
Second
Clamp Close Profile Setpoints 2–10 . . . . . . . . . . . . . . .
Third
Clamp Close Profile Setpoints 2–1 1. . . . . . . . . . . . . . . .
Clamp
Low Pressure Close Profile Setpoints 2–12 . . . . . . . . . .
Critical Process Setpoints
2–12 . . . . . . . . . . . . . . . . . . . . . . . .
DYC – Dynamic Command Block
2–13 . . . . . . . . . . . . . . . . . . . .
Bit-mapped
Control W ords 2–13 . . . . . . . . . . . . . . . . . . . . . . .
Direct
Set-output V alues 2–25 . . . . . . . . . . . . . . . . . . . . . . . . .
Direct
Set-output Ramp Rates 2–25 . . . . . . . . . . . . . . . . . . . .