User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover
1–20 Abbreviated Command and Status Blocks
Publication
1771-6.5.88 – July 1997
Ram (Screw) Pressure Sensor Configuration (continued)
MCC17
N40:13 Minimum pressure
MCC18 N40:14 Maximum pressure
MCC19 N40:15 Analog signal @ min pressure
MCC20 N40:16 Analog signal @ max pressure
MCC21 N40:17 High pressure alarm setpoint
MCC22 N40:18 Time delay for pressure alarms
Clamp Position Sensor Configuration
MCC23 N40:19 Minimum position
MCC24 N40:20 Maximum position
MCC25 N40:21 Analog signal @ min position
MCC26 N40:22 Analog signal @ max position
MCC27 N40:23 Minimum SWTL
MCC28 N40:24 Maximum SWTL
MCC29 N40:25 SWTL alarm deadband
MCC30 N40:26 Digital filter
Clamp Pressure Sensor Configuration
MCC31 N40:27 Minimum pressure
MCC32 N40:28 Maximum pressure
MCC33 N40:29 Analog signal @ min pressure
MCC34 N40:30 Analog signal @ max pressure
MCC35 N40:31 High pressure alarm setpoint
MCC36 N40:32 Time delay for pressure alarms
Ejector Position Sensor Configuration
MCC37 N40:33 Minimum position
MCC38 N40:34 Maximum position
MCC39 N40:35 Analog signal @ min position
MCC40 N40:36 Analog signal @ max position
MCC41 N40:37 Minimum SWTL
MCC42 N40:38 Maximum SWTL
MCC43 N40:39 SWTL alarm deadband
MCC44 N40:40 Digital filter
Ejector Pressure Sensor Configuration
MCC45 N40:41 Minimum pressure
MCC46 N40:42 Maximum pressure
MCC47 N40:43 Analog signal @ min pressure
MCC48 N40:44 Analog signal @ max pressure
MCC49 N40:45 High pressure alarm setpoint
MCC50 N40:46 Time delay for pressure alarms
Screw RPM Sensor Configuration
MCC51 N40:47 Minimum RPM
MCC52 N40:48 Maximum RPM
MCC53 N40:49 Analog signal @ min RPM
MCC54 N40:50 Analog signal @ max RPM
MCC55 N40:51 High RPM alarm setpoint
MCC56 N40:52 Time delay for RPM alarms
Cavity (or System) Pressure Sensor Configuration
MCC57 N40:53 Minimum pressure
MCC58 N40:54 Maximum pressure
MCC59 N40:55 Analog signal @ min pressure