User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover
5–2 Module Specifications
Publication
1771-6.5.88 – July 1997
The following table lists process control options.
Phase: Type of Profile: Mode:
Injection phase: 10-step profile with
selectable transition
velocity vs. position
or
velocity vs. position pressure limited
or
injection pressure vs. position
or
injection pressure vs. time
open/closed with ERC
open/closed with ERC
open/closed with ERC
open/closed with ERC
Selectable Transition dependent on:
S
Time
S
Ram (screw) pressure
S
Cavity pressure
S
or Ram (screw) position
N/A N/A
Pack phase: 5-step profile ram (screw) pressure vs. time
or
cavity pressure vs. time
open/closed with ERC
open/closed with ERC
Hold phase: 5-step profile ram (screw) pressure vs. time
or
cavity pressure vs. time
open/closed with ERC
open/closed with ERC
Plastication phase: 10-step profile backpressure vs. position
or
backpressure vs. time
or
screw RPM vs. position
or
screw RPM vs. time
open/closed with ERC
open/closed with ERC
open/closed with ERC
open/closed with ERC
Clamp close phase: three 3-step profiles
(for a total of 9 steps)
velocity vs. position
or
pressure vs. position
open/closed with ERC
open/closed with ERC
Clamp low pressure close with re-try: 2-step profile pressure vs. position open/closed with ERC
Clamp open phase: three 3-step profiles
(for a total of 9 steps)
velocity vs. position
or
pressure vs. position
open/closed with ERC
open/closed with ERC
Clamp open slow phase: 2-step profile velocity vs. position
or
pressure vs. position
open/closed with ERC
open/closed with ERC
Ejector adv. phase: 3-step profile (with tip strokes) velocity vs. position
or
pressure vs. position
open/closed with ERC
open/closed with ERC
Ejector ret. phase: 3-step profile velocity vs. position
or
pressure vs. position
open/closed with ERC
open/closed with ERC
Alarms Process
Programming
N/A
Control Options P, I, PI, PD, PID, and FF
Expert Response Compensation
Open/Closed Loop
N/A
Process Control Options