User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover

4–9Programming Error Codes
Publication
1771-6.5.88 – July 1997
ID = 4
SCC – Second Clamp Close Configuration Block
Error Code
Description
ID = 4
0205
SCC05 is out of range. Valid range is 00000
≤
SCC05
≤
09999
0206
SCC06 is out of range. Valid range is 00000
≤
SCC06
≤
09999
0208
SCC08 is out of range. Valid range is 00000
≤
SCC08
≤
09999
0209
SCC09 is out of range. Valid range is 00000
≤
SCC09
≤
09999
0210
SCC10 is out of range. Valid range is 00000
≤
SCC10
≤
09999
0211
SCC11 is out of range. Valid range is 00000
≤
SCC11
≤
09999
0212
SCC12 is out of range. Valid range is 00000
≤
SCC12
≤
09999
0213
SCC13 is out of range. Valid range is 00000
≤
SCC13
≤
09999
0214
SCC14 is out of range. Valid range is 00000
≤
SCC14
≤
09999
0215
SCC15 is out of range. Valid range is 00000
≤
SCC15
≤
09999
0216
SCC16 is out of range. Valid range is 00000
≤
SCC16
≤
09999
0217
SCC17 is out of range. Valid range is 00000
≤
SCC17
≤
09999
0218
SCC18 is out of range. Valid range is 00000
≤
SCC18
≤
09999
0219
SCC19 is out of range. Valid range is 00000
≤
SCC19
≤
09999
0220
SCC20 is out of range. Valid range is 00000
≤
SCC20
≤
09999
0221
SCC21 is out of range. Valid range is 00000
≤
SCC21
≤
09999
0222
SCC22 is out of range. Valid range is 00000
≤
SCC22
≤
09999
0223
SCC23 is out of range. Valid range is 00000
≤
SCC23
≤
09999
0224
SCC24 is out of range. Valid range is 00000
≤
SCC24
≤
09999
0225
SCC25 is out of range. Valid range is 00000
≤
SCC25
≤
09999
0226
SCC26 is out of range. Valid range is 00000
≤
SCC26
≤
09999
0227
SCC27 is out of range. Valid range is 00000
≤
SCC27
≤
09999
0228
SCC28 is out of range. Valid range is 00000
≤
SCC28
≤
09999
0229
SCC29 is out of range. Valid range is 00000
≤
SCC29
≤
09999
0230
SCC30 is out of range. Valid range is 00000
≤
SCC30
≤
09999
0231
SCC31 is out of range. Valid range is 00000
≤
SCC31
≤
09999
0232
SCC32 is out of range. Valid range is 00000
≤
SCC32
≤
09999
0233
SCC33 is out of range. Valid range is 00000
≤
SCC33
≤
09999
0234
SCC34 is out of range. Valid range is 00000
≤
SCC34
≤
09999
0235
SCC35 is out of range. Valid range is 00000
≤
SCC35
≤
09999
0236
SCC36 is out of range. Valid range is 00000
≤
SCC36
≤
09999
0237
SCC37 is out of range. Valid range is 00000
≤
SCC37
≤
09999
0238
SCC38 is out of range. Valid range is 00000
≤
SCC38
≤
09999
0239
SCC39 is out of range. Valid range is 00000
≤
SCC39
≤
09999
0240
SCC40 is out of range. Valid range is 00000
≤
SCC40
≤
09999
0243
SCC43 is out of range. Valid range is 00000
≤
SCC43
≤
09999
0244
SCC44 is out of range. Valid range is 00000
≤
SCC44
≤
09999
0247
SCC47 is out of range. Valid range is 00000
≤
SCC47
≤
09999
0248
SCC48 is out of range. Valid range is 00000
≤
SCC48
≤
09999
0249
SCC49 is out of range. Valid range is 00000
≤
SCC49
≤
09999
0250
SCC50 is out of range. Valid range is 00000
≤
SCC50
≤
09999
0251
SCC51 is out of range. Valid range is 00000
≤
SCC51
≤
09999
0252
SCC52 is out of range. Valid range is 00000
≤
SCC52
≤
09999