User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover
3–21Status Word/Bit Descriptions
Publication
1771-6.5.88 – July 1997
PPS
Word Bit Description
B06 Segment 7
B07 Segment 8
B08 Segment 9
B09 Segment 10
B10 Segment 11
B11-B15 Open
Plastication Profile Actuals
Word Description
PPS09 Actual Segment 1 RPM [25] Average RPM during last Segment 1.
PPS10 Actual Segment 1 Pressure [01] Average ram (screw) pressure during last Segment 1.
PPS11 Actual Segment 1 Execution Time [21] Time required for last Segment 1.
PPS12 Actual End of Segment 1 Position [12] Ram (Screw) position at completion of last Segment 1.
PPS13 Actual Segment 2 RPM [25] Average RPM during last Segment 2.
PPS14 Actual Segment 2 Pressure [01] Average ram (screw) pressure during last Segment 2.
PPS15 Actual Segment 2 Execution Time [21] Time required for last Segment 2.
PPS16 Actual End of Segment 2 Position [12] Ram (Screw) position at completion of last Segment 2.
PPS17 Actual Segment 3 RPM [25] Average RPM during last Segment 3.
PPS18 Actual Segment 3 Pressure [01] Average ram (screw) pressure during last Segment 3.
PPS19 Actual Segment 3 Execution Time [21] Time required for last Segment 3.
PPS20 Actual End of Segment 3 Position [12] Ram (Screw) position at completion of last Segment 3.
PPS21 Actual Segment 4 RPM [25] Average RPM during last Segment 4.
PPS22 Actual Segment 4 Pressure [01] Average ram (screw) pressure during last Segment 4.
PPS23 Actual Segment 4 Execution Time [21] Time required for last Segment 4.
PPS24 Actual End of Segment 4 Position [12] Ram (Screw) position at completion of last Segment 4.
PPS25 Actual Segment 5 RPM [25] Average RPM during last Segment 5.
PPS26 Actual Segment 5 Pressure [01] Average ram (screw) pressure during last Segment 5.
PPS27 Actual Segment 5 Execution Time [21] Time required for last Segment 5.
PPS28 Actual End of Segment 5 Position [12] Ram (Screw) position at completion of last Segment 5.
PPS29 Actual Segment 6 RPM [25] Average RPM during last Segment 6.
PPS30 Actual Segment 6 Pressure [01] Average ram (screw) pressure during last Segment 6.
PPS31 Actual Segment 6 Execution Time [21] Time required for last Segment 6.
PPS32 Actual End of Segment 6 Position [12] Ram (Screw) position at completion of last Segment 6.
PPS33 Actual Segment 7 RPM [25] Average RPM during last Segment 7.
PPS34 Actual Segment 7 Pressure [01] Average ram (screw) pressure during last Segment 7.
PPS35 Actual Segment 7 Execution Time [21] Time required for last Segment 7.
PPS36 Actual End of Segment 7 Position [12] Ram (Screw) position at completion of last Segment 7.
PPS37 Actual Segment 8 RPM [25] Average RPM during last Segment 8.
PPS38 Actual Segment 8 Pressure [01] Average ram (screw) pressure during last Segment 8.
PPS39 Actual Segment 8 Execution Time [21] Time required for last Segment 8.
PPS40 Actual End of Segment 8 Position [12] Ram (Screw) position at completion of last Segment 8.
PPS41 Actual Segment 9 RPM [25] Average RPM during last Segment 9.
PPS42 Actual Segment 9 Pressure [01] Average ram (screw) pressure during last Segment 9.
PPS43 Actual Segment 9 Execution Time [21] Time required for last Segment 9.
PPS44 Actual End of Segment 9 Position [12] Ram (Screw) position at completion of last Segment 9.
PPS45 Actual Segment 10 RPM [25] Average RPM during last Segment 10.
PPS46 Actual Segment 10 Pressure [01] Average ram (screw) pressure during last Segment 10.