User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ú Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover
2–99Command Word/Bit Descriptions
Publication
1771-6.5.88 – July 1997
SCC
Output Ramp Rate
The module uses the following ramp rates when moving its outputs
from setpoint to setpoint during the Second Clamp Close Profile.
The module interprets a ramp rate entry of zero as a step function
ramp (ramp disable).
Word Description
SCC17 Output #1 Acceleration Ramp Rate during Profile [20]
SCC18 Output #2 Acceleration Ramp Rate during Profile [20]
SCC19 Output #3 Acceleration Ramp Rate during Profile [20]
SCC20 Output #4 Acceleration Ramp Rate during Profile [20]
SCC21 Output #5 Acceleration Ramp Rate during Profile [20]
SCC22 Output #6 Acceleration Ramp Rate during Profile [20]
SCC23 Output #7 Acceleration Ramp Rate during Profile [20]
SCC24 Output #8 Acceleration Ramp Rate during Profile [20]
SCC25 Output #1 Deceleration Ramp Rate during Profile [20]
SCC26 Output #2 Deceleration Ramp Rate during Profile [20]
SCC27 Output #3 Deceleration Ramp Rate during Profile [20]
SCC28 Output #4 Deceleration Ramp Rate during Profile [20]
SCC29 Output #5 Deceleration Ramp Rate during Profile [20]
SCC30 Output #6 Deceleration Ramp Rate during Profile [20]
SCC31 Output #7 Deceleration Ramp Rate during Profile [20]
SCC32 Output #8 Deceleration Ramp Rate during Profile [20]
End of Profile Set-output Values
When the module completes the second clamp close profile and
CPC03-B09 is set, it:
• sets its outputs to the following values
• sets status bit SYS22-B01
• uses ramp rates SCC17 - 32 when changing outputs to these values
Use these values for setting cores if applied before starting the Third
Clamp Close Profile:
Word Description
SCC33 Output #1 Set-output Value at End of Profile [19]
SCC34 Output #2 Set-output Value at End of Profile [19]
SCC35 Output #3 Set-output Value at End of Profile [19]
SCC36 Output #4 Set-output Value at End of Profile [19]
SCC37 Output #5 Set-output Value at End of Profile [19]
SCC38 Output #6 Set-output Value at End of Profile [19]
SCC39 Output #7 Set-output Value at End of Profile [19]
SCC40 Output #8 Set-output Value at End of Profile [19]