User Manual
Table Of Contents
- 1771-6.5.88, Plastic Molding Module Reference Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Abbreviated Command and Status Blocks
- Chapter Contents
- CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC - Plastication Configuration Block
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post- decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS - Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 2 - Command Word/Bit Descriptions
- Alphabetical List of Command Blocks and Block ID Codes
- List of Data Words
- Engineering Units
- Data Blocks Require I/O Configuration
- Data Blocks for System Control
- Data Blocks for Controlling Ram (Screw) Position
- Data Blocks for Controlling Clamp Position
- Data Blocks for Controlling Ejector Position
- Sensors Required
- CLC CLC - Clamp and Eject ERC Values Block
- CPC - Clamp Close Profile Block
- DYC DYC - Dynamic Command Block
- EAC - Ejector Advance Configuration Block
- EPC - Ejector Profile Block
- ERC - Ejector Retract Configuration Block
- FCC - First Clamp Close Configuration Block
- FOC - First Clamp Open Configuration Block
- HDC - Hold Configuration Block
- HPC - Pack/Hold Profile Block
- INC - Injection Configuration Block
- IPC - Injection Profile Block
- JGC - Jog Configuration Block
- LPC - Clamp Low Pressure Close Configuration Block
- MCC - Module Configuration Command Block
- OPC - Clamp Open Profile Block
- OSC - Clamp Open Slow Configuration Block
- PKC - Pack Configuration Block
- PLC Plastication Configuration Command Block (PLC)
- PPC - Plastication Profile Block
- PRC - Pre-decompression Configuration Block
- PSC - Post-decompression Configuration Block
- PTC - Process Trace Configuration Block
- RLC - Inject ERC Values Block
- SCC - Second Clamp Close Configuration Block
- SOC - Second Clamp Open Configuration Block
- TCC - Third Clamp Close Configuration Block
- TOC - Third Clamp Open Configuration Block
- 3 - Word/Bit Descriptions
- List of Status Blocks and Block ID Codes
- List of Data Words
- Data Blocks Require I/O Configuration
- Engineering Units
- Status Block for Reporting System Status
- Status Blocks for Reporting Ram (Screw) Position
- Status Blocks for Reporting Clamp Position
- Status Blocks for Reporting Ejector Position
- CLS - Clamp and Eject ERC Values Status Block
- CPS - Clamp Close Profiles Status Block
- EPS - Ejector Profile Status Block
- HPS - Pack/Hold Profile Status Block
- IPS ΓΊ Injection Profile Status Block
- OPS - Clamp Open Profiles Status Block
- PPS - Plastication Profile Status Block
- PTS - Process Trace Status Block
- RLS - Inject ERC Values Status Block
- SYS - System Status Block
- 4 - Programming Error Codes
- 5 - Module Specifications
- 6 - Calibration Instructions
- A - Single transfer for Reporting Ejector Status
- Back cover

2β68 Command Word/Bit Descriptions
Publication
1771-6.5.88 β July 1997
Notes: 1. For [ ] engineering units, see page 3.
2. When using the Inject/Clamp/Eject mode, all pressure readings are system pressure at input 2, except where noted.
Bit-mapped Control Words
Word Bit Description
MCC01
B00 - B07 Block ID 00000001
B08 - B15 Reserved for the module. Do not use.
MCC02
MCC Configuration Selections
B00 Data Range Selection
0 English Units (Inches and PSI)
0 = English Units (Inches and PSI)
1 = Metric Units (Millimeters and Bar)
B01 Module designation for co-injection
0 = QIA
1 = QIB
B02 Open
B03 Module I/O Density
B03
Module
I/O
Density
0 = invalid
0
=
invalid
1 = Four/Four I/O (required selection)
Four/Four I/O Configuration
Four/Four
I/O
Configuration
MUST BE SET. The module configures itself as a 1-slot module containing four inputs and four outputs,
MUST
BE
SET
.
The
module
configures
itself
as
a
1 slot
module
containing
four
in uts
and
four
out uts
,
and accesses bits MCC02-B04 and MCC02-B05 to determine layout of its inputs.
B04 -B05 B05 B04 Four/Four I/O Configuration
0 0 Inject Control
0 1 Inject and Clamp Control
1 0 Clamp and Eject Control
1 0 Clam
and
Eject
Control
1 1 Inject, Clamp, and Eject Control
B05 B04 Input #1 Input #2 Input #3 Input #4
0 0 Ram (Screw) Position Ram (Screw) Pressure Screw RPM Cavity Pressure
0 1 R (S ) P iti R (S ) P Cl P iti Cl P
() () y
0 1 Ram (Screw) Position Ram (Screw) Pressure Clamp Position Clamp Pressure
1 0 Ejector Position Ejector Pressure Clamp Position Clamp Pressure
1 1 Ram (Screw) Position System Pressure Clamp Position Ejector Position
The module accesses these bits only if MCC02-B03 is SET.
B06-B07 Open
B08 inhibit (override) loss of sensor protection for screw position input
B09 Inhibit (override) loss of sensor protection for screw pressure input
B10 Inhibit (override) loss of sensor protection for clamp position input
B11 Inhibit (override) loss of sensor protection for clamp pressure input
B12 Inhibit (override) loss of sensor protection for ejector position input
B13 Inhibit (override) loss of sensor protection for ejector pressure input
B14 Inhibit (override) loss of sensor protection for screw RPM input
B15 Inhibit (override) loss of sensor protection for cavity pressure input (system pressure in Inject-Clamp-Eject mode)
MCC β Module Configuration
Command Block