User Manual

Table of Contents
ix
Clamp Open Slow Profile Actuals 3–19 . . . . . . . . . . . . . . . . . .
Open Profile Maximum Pressures
3–19 . . . . . . . . . . . . . . . . . .
Open
Profile Execution T imes 3–20 . . . . . . . . . . . . . . . . . . . . .
PPS
– Plastication Profile Status Block 3–20 . . . . . . . . . . . . . . . .
Bit-mapped Status Words
3–20 . . . . . . . . . . . . . . . . . . . . . . . .
Plastication
Profile Actuals 3–21 . . . . . . . . . . . . . . . . . . . . . . .
Plastication Maximum Pressure
3–22 . . . . . . . . . . . . . . . . . . .
Post-decompression Maximum Pressure
3–22 . . . . . . . . . . . . .
Execution
T imes 3–22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Post-decompression Movement Actuals
3–22 . . . . . . . . . . . . .
Shot Size Actual
3–22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PTS – Process Trace Status Block
3–22 . . . . . . . . . . . . . . . . . . .
Bit-mapped Status Words
3–22 . . . . . . . . . . . . . . . . . . . . . . . .
RLS – Inject ERC Values Status Block
3–24 . . . . . . . . . . . . . . . . .
Bit-mapped Status Words
3–24 . . . . . . . . . . . . . . . . . . . . . . . .
Injection Profile ERC Actuals
3–24 . . . . . . . . . . . . . . . . . . . . .
Pack Profile ERC Actuals
3–24 . . . . . . . . . . . . . . . . . . . . . . . .
Hold Profile ERC Actuals
3–25 . . . . . . . . . . . . . . . . . . . . . . . .
Plastication Profile ERC Actuals
3–25 . . . . . . . . . . . . . . . . . . .
SYS – System Status Block
3–25 . . . . . . . . . . . . . . . . . . . . . . . .
Input
Level In Engineering Units 3–46 . . . . . . . . . . . . . . . . . . .
Input
Level, Raw Signal 3–46 . . . . . . . . . . . . . . . . . . . . . . . . .
Output
Level in Percentage 3–46 . . . . . . . . . . . . . . . . . . . . . .
Cycle Maximum Pressures
3–47 . . . . . . . . . . . . . . . . . . . . . . .
Process
T race Data Collection Status 3–47 . . . . . . . . . . . . . . .
Process T imes 3–48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics
3–48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New Status Confirmation 3–48 . . . . . . . . . . . . . . . . . . . . . . . .
Programming Error Codes 4–1. . . . . . . . . . . . . . . . . . . . .
How to Read Error Codes 4–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
ID
= 1 – MCC – Module Configuration Command Block 4–3 . . . .
ID
= 2 – JGC – Jog Configuration Block 4–6 . . . . . . . . . . . . . . . .
ID
= 3 – FCC – First Clamp Close Configuration Block 4–7 . . . . .
ID
= 4 – SCC – Second Clamp Close Configuration Block 4–9 . . .
ID
= 5 – TCC – Third Clamp Close Configuration Block 4–10 . . . . .
ID
= 6 – LPC – Clamp Low Pressure Close Configuration Block 4–1 1
ID = 7 – CPC – Clamp Close Profile Block 4–12 . . . . . . . . . . . . . .
ID
= 8 – INC – Injection Configuration Block 4–17 . . . . . . . . . . . . .
ID
= 9 – IPC – Injection Profile Block 4–18 . . . . . . . . . . . . . . . . . .
ID
= 10 – PKC – Pack Configuration Block 4–25 . . . . . . . . . . . . . .
ID
= 1 1 – HDC – Hold Configuration Block 4–26 . . . . . . . . . . . . . .
ID = 12 – HPC – Pack/Hold Profile Block
4–28 . . . . . . . . . . . . . . .
ID = 13 – PRC – Pre-Decompression Configuration Block
4–30 . . .
ID
= 14 – PLC – Plastication Configuration Block 4–31 . . . . . . . . .