Manual

Enter Y our V alues Here
Blank Worksheets
Appendix A
A-33
Worksheet 8-C (continued)
Ejector (EPC) Profile Block
Control Word ProSet 600 Addr. Value Description Units
EPC09 N45:125 Full Advance Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC10 N45:126 Full Advance Segment 1 Pressure Setpoint Pressure
3
EPC11 N45:127 End of Full Advance Segment 1 Position Setpoint Incremental Distance
4
EPC12 N45:128 Full Advance Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC13 N45:129 Full Advance Segment 2 Pressure Setpoint Pressure
3
EPC14 N45:130 End of Full Advance Segment 2 Position Setpoint Incremental Distance
4
EPC15 N45:131 Full Advance Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC16 N45:132 Full Advance Segment 3 Pressure Setpoint Pressure
3
EPC21 N45:137 Tip Retract Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC22 N45:138 Tip Retract Pressure Setpoint Pressure
3
EPC23 N45:139 End of Tip Retract Position Setpoint Incremental Distance
4
EPC27 N45:143 Tip Advance Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC28 N45:144 Tip Advance Pressure Setpoint Pressure
3
EPC29 N45:145 End of Tip Advance Position Setpoint Incremental Distance
4
EPC33 N45:149 Full Retract Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC34 N45:150 Full Retract Segment 1 Pressure Setpoint Pressure
3
EPC35 N45:151 End of Full Retract Segment 1 Position Setpoint Incremental Distance
4
EPC36 N45:152 Full Retract Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC37 N45:153 Full Retract Segment 2 Pressure Setpoint Pressure
3
EPC38 N45:154 End of Full Retract Segment 2 Position Setpoint Incremental Distance
4
EPC39 N45:155 Full Retract Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC40 N45:156 Full Retract Segment 3 Pressure Setpoint Pressure
3
EPC57 N41:173 Ejector Forward Dwell timer Preset Time
5
EPC59 N41:175 Ejector Fully Advanced Position Setpoint Incremental Distance
4
EPC60 N41:176 Ejector Fully Retracted Position Setpoint Incremental Distance
4
EPC61 N41:177 Clamp Position for Start of Eject Profile Incremental Distance
6
EPC62 N41:178 Clamp Position for Ejector Inhibit Incremental Distance
6
EPC63 N41:179 Ejector Position for Clamp Close Enable Incremental Distance
4
EPC64 N45:180 Ejector Strokes Required Number of Strokes
1
Ejector Percent of Maximum V elocity
2
Ejector V elocity along Axis
3
Ejector Pressure
00.00 to 99.99 00.00 to 99.99 Inches per Second 0000 to 9999 PSI
000.0 to 999.9 Millimeters per Second
000.0 to 999.9 Bar
4
Clamp Axis Measured from MCC27
5
Time
6
Clamp Axis Measured from MCC27
(if nonzero) or MCC23 00.00 to 99.99 Seconds (if nonzero) or MCC23
00.00 to 99.99 Inches 00.00 to 99.99 Inches
00.00 to 999.9 Millimeters 000.0 to 999.9 Millimeters