Manual

Enter Y our V alues Here
Load Initial Profile Values for
Machine Tuning
Chapter 8
8-15
Worksheet 8-C (continued)
Ejector (EPC) Profile Block
Control Word ProSet 600 Addr. Value Description Units
EPC09 N45:125 0 Full Advance Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC10 N45:126 0 Full Advance Segment 1 Pressure Setpoint Pressure
3
EPC11 N45:127 0 End of Full Advance Segment 1 Position Setpoint Incremental Distance
4
EPC12 N45:128 0 Full Advance Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC13 N45:129 0 Full Advance Segment 2 Pressure Setpoint Pressure
3
EPC14 N45:130 0 End of Full Advance Segment 2 Position Setpoint Incremental Distance
4
EPC15 N45:131 0 Full Advance Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC16 N45:132 0 Full Advance Segment 3 Pressure Setpoint Pressure
3
EPC21 N45:137 0 Tip Retract Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC22 N45:138 0 Tip Retract Pressure Setpoint Pressure
3
EPC23 N45:139 0 End of Tip Retract Position Setpoint Incremental Distance
4
EPC27 N45:143 0 Tip Advance Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC28 N45:144 0 Tip Advance Pressure Setpoint Pressure
3
EPC29 N45:145 0 End of Tip Advance Position Setpoint Incremental Distance
4
EPC33 N45:149 0 Full Retract Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC34 N45:150 0 Full Retract Segment 1 Pressure Setpoint Pressure
3
EPC35 N45:151 0 End of Full Retract Segment 1 Position Setpoint Incremental Distance
4
EPC36 N45:152 0 Full Retract Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC37 N45:153 0 Full Retract Segment 2 Pressure Setpoint Pressure
3
EPC38 N45:154 0 End of Full Retract Segment 2 Position Setpoint Incremental Distance
4
EPC39 N45:155 0 Full Retract Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or
Velocity along Axis
2
EPC40 N45:156 0 Full Retract Segment 3 Pressure Setpoint Pressure
3
EPC57 N45:173 0 Ejector Forward Dwell timer Preset Time
5
EPC59 N45:175 * Ejector Fully Advanced Position Setpoint Incremental Distance
4
EPC60 N45:176 * Ejector Fully Retracted Position Setpoint Incremental Distance
4
EPC61 N45:177 * Clamp Position for Start of Eject Profile Incremental Distance
6
EPC62 N45:178 * Clamp Position for Ejector Inhibit Incremental Distance
6
EPC63 N45:179 * Ejector Position for Clamp Close Enable Incremental Distance
4
EPC64 N45:180 1 Ejector Strokes Required Number of Strokes
1
Ejector Percent of Maximum V elocity
2
Ejector V elocity along Axis
3
Ejector Pressure
00.00 to 99.99 00.00 to 99.99 Inches per Second 0000 to 9999 PSI
000.0 to 999.9 Bar
4
Clamp Axis Measured from MCC27
5
Time
6
Clamp Axis Measured from MCC27
(if nonzero) or MCC23 00.00 to 99.99 Seconds (if nonzero) or MCC23
00.00 to 99.99 Inches 00.00 to 99.99 Inches
00.00 to 999.9 Millimeters 000.0 to 999.9 Millimeters
* Refer to the appropriate section later in this chapter for information on this parameter