Manual

Enter Y our V alues Here
Load Initial Profile Values for
Machine Tuning
Chapter 8
8-9
Worksheet 8-B (continued)
Clamp Open (OPC) Profile Block
Control Word ProSet 600 Addr. Value Description Units
OPC09 N43:545 0 FOC Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC10 N43:546 0 FOC Segment 1 Pressure Setpoint Pressure
3
OPC11 N43:547 * FOC EndofSegment 1 Position Setpoint Incremental Distance
4
OPC12 N43:548 0 FOC Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC13 N43:549 0 FOC Segment 2 Pressure Setpoint Pressure
3
OPC14 N43:550 * FOC EndofSegment 2 Position Setpoint Incremental Distance
4
OPC15 N43:551 0 FOC Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC16 N43:552 0 FOC Segment 3 Pressure Setpoint Pressure
3
OPC17 N43:553 * FOC EndofSegment 3 Position Setpoint Incremental Distance
4
OPC18 N43:554 0 SOC Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC19 N43:555 0 SOC Segment 1 Pressure Setpoint Pressure
3
OPC20 N43:556 0 SOC EndofSegment 1 Position Setpoint Incremental Distance
4
OPC21 N43:557 0 SOC Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC22 N43:558 0 SOC Segment 2 Pressure Setpoint Pressure
3
OPC23 N43:559 0 SOC EndofSegment 2 Position Setpoint Incremental Distance
4
OPC24 N43:560 0 SOC Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC25 N43:561 0 SOC Segment 3 Pressure Setpoint Pressure
3
OPC26 N43:562 0 SOC EndofSegment 3 Position Setpoint Incremental Distance
4
OPC27 N43:563 0 TOC Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC28 N43:564 0 TOC Segment 1 Pressure Setpoint Pressure
3
OPC29 N43:565 0 TOC EndofSegment 1 Position Setpoint Incremental Distance
4
OPC30 N43:566 0 TOC Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC31 N43:567 0 TOC Segment 2 Pressure Setpoint Pressure
3
OPC32 N43:568 0 TOC EndofSegment 2 Position Setpoint Incremental Distance
4
OPC33 N43:569 0 TOC Segment 3 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC34 N43:570 0 TOC Segment 3 Pressure Setpoint Pressure
3
OPC35 N43:571 0 TOC EndofSegment 3 Position Setpoint Incremental Distance
4
OPC36 N43:572 0 OSC Segment 1 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC37 N43:573 0 OSC Segment 1 Pressure Setpoint Pressure
3
OPC38 N43:574 0 OSC EndofSegment 1 Position Setpoint Incremental Distance
4
OPC39 N43:575 0 OSC Segment 2 Velocity Setpoint Percent of Maximum Velocity
1
or Velocity along Axis
2
OPC40 N43:576 0 OSC Segment 2 Pressure Setpoint Pressure
3
OPC61 N43:597 * Start OSC Position Setpoint Incremental Distance
4
OPC62 N43:598 * Mold Open Position Setpoint Incremental Distance
4
OPC63 N43:599 0 Mold Open Dwell Timer Preset Time
5
1
Clamp Percent of Maximum V elocity
2
Clamp V elocity along Axis
3
Clamp Pressure
00.00 to 99.99 00.00 to 99.99 Inches per Second 0000 to 9999 PSI
000.0 to 999.9 Bar
4
Clamp Axis Measured from MCC27 (if nonzero) or MCC23
5
Time
00.00 to 99.99 Inches 00.00 to 99.99 Seconds
00.00 to 999.9 Millimeters
* Refer to the appropriate section later in this chapter for information on this parameter