Instruction Manual

Enter Y our V alues Here
Blank Worksheets
Appendix A
A-23
Control Word
ProSet 600 Addr. Value Description Units
PPC09 N44:425 * Segment 1 RPM Setpoint RPM
5
PPC10 N44:426 * Segment 1 Pressure Setpoint Pressure
3
PPC11 N44:427 * Endof Segment 1 Position Setpoint Distance from Moldend
2
PPC12 N44:428 100 Segment 1 Time Setpoint Time
1
PPC13 N44:429 * Segment 2 RPM Setpoint RPM
5
PPC14 N44:430 * Segment 2 Pressure Setpoint Pressure
3
PPC15 N44:431 * Endof Segment 2 Position Setpoint Distance from Moldend
2
PPC16 N44:432 100 Segment 2 Time Setpoint Time
1
PPC17 N44:433 * Segment 3 RPM Setpoint RPM
5
PPC18 N44:434 * Segment 3 Pressure Setpoint Pressure
3
PPC19 N44:435 * Endof Segment 3 Position Setpoint Distance from Moldend
2
PPC20 N44:436 100 Segment 3 Time Setpoint Time
1
PPC21 N44:437 * Segment 4 RPM Setpoint RPM
5
PPC22 N44:438 * Segment 4 Pressure Setpoint Pressure
3
PPC23 N44:439 * Endof Segment 4 Position Setpoint Distance from Moldend
2
PPC24 N44:440 100 Segment 4 Time Setpoint Time
1
PPC25 N44:441 * Segment 5 RPM Setpoint RPM
5
PPC26 N44:442 * Segment 5 Pressure Setpoint Pressure
3
PPC27 N44:443 * Endof Segment 5 Position Setpoint Distance from Moldend
2
PPC28 N44:444 100 Segment 5 Time Setpoint Time
1
PPC29 N44:445 * Segment 6 RPM Setpoint RPM
5
PPC30 N44:446 * Segment 6 Pressure Setpoint Pressure
3
PPC31 N44:447 * Endof Segment 6 Position Setpoint Distance from Moldend
2
PPC32 N44:448 100 Segment 6 Time Setpoint Time
1
PPC33 N44:449 * Segment 7 RPM Setpoint RPM
5
PPC34 N44:450 * Segment 7 Pressure Setpoint Pressure
3
PPC35 N44:451 * Endof Segment 7 Position Setpoint Distance from Moldend
2
PPC36 N44:452 100 Segment 7 Time Setpoint Time
1
PPC37 N44:453 * Segment 8 RPM Setpoint RPM
5
PPC38 N44:454 * Segment 8 Pressure Setpoint Pressure
3
PPC39 N44:455 * Endof Segment 8 Position Setpoint Distance from Moldend
2
PPC40 N44:456 100 Segment 8 Time Setpoint Time
1
PPC41 N44:457 * Segment 9 RPM Setpoint RPM
5
PPC42 N44:458 * Segment 9 Pressure Setpoint Pressure
3
PPC43 N44:459 * Endof Segment 9 Position Setpoint Distance from Moldend
2
PPC44 N44:460 100 Segment 9 Time Setpoint Time
1
PPC45 N44:461 * Segment 10 RPM Setpoint RPM
5
PPC46 N44:462 * Segment 10 Pressure Setpoint Pressure
3
PPC47 N44:463 * Endof Segment 10 Position Setpoint Distance from Moldend
2
PPC48 N44:464 100 Segment 10 Time Setpoint Time
1
PPC49 N44:465 * Segment 11 RPM Setpoint RPM
5
PPC50 N44:466 * Segment 11 Pressure Setpoint Pressure
3
PPC51 N44:467 * RPM Profile Offset RPM
5
PPC52 N44:468 * Pressure Profile Offset Pressure
3
PPC61 N44:477 0 Cushion Size Distance from Moldend
2
PPC62 N44:478 * Shot Size Incremental Distance
4
1
Time
2
Distance from MCC13 (if not zero) or MCC09
3
Pressure
4
Distance from PPC61
5
Screw Speed
00.00 to 99.99 Seconds 00.00 to 99.99 Inches 0000 to 9999 PSI 00.00 to 99.99 Inches 000.0 to 999.9 RPM
000.0 to 999.9 Millimeters 000.0 to 999.9 Bar 000.0 to 999.9 Millimeter
* Refer to the appropriate section later in this chapter for information on this parameter