Instruction Manual

Enter Y our V alues Here
Load Initial Profile Values
Chapter 8
8-11
W orksheet 8B (continued)
Pack/Hold Profile Command Block (HPC)
Control Word ProSet 600 Addr. Value Description Units
HPC09 N44:245 0 Pack Segment 1 Cavity Pressure Setpoint Pressure
2
HPC10 N44:246 * Pack Segment 1 Ram (screw) Pressure Setpoint Pressure
3
HPC11 N44:247 100 Pack Segment 1 Time Setpoint Time
1
HPC12 N44:248 0 Pack Segment 2 Cavity Pressure Setpoint Pressure
2
HPC13 N44:249 * Pack Segment 2 Ram (screw) Pressure Setpoint Pressure
3
HPC14 N44:250 100 Pack Segment 2 Time Setpoint Time
1
HPC15 N44:251 0 Pack Segment 3 Cavity Pressure Setpoint Pressure
2
HPC16 N44:252 * Pack Segment 3 Ram (screw) Pressure Setpoint Pressure
3
HPC17 N44:253 100 Pack Segment 3 Time Setpoint Time
1
HPC18 N44:254 0 Pack Segment 4 Cavity Pressure Setpoint Pressure
2
HPC19 N44:255 * Pack Segment 4 Ram (screw) Pressure Setpoint Pressure
3
HPC20 N44:256 100 Pack Segment 4 Time Setpoint Time
1
HPC21 N44:257 0 Pack Segment 5 Cavity Pressure Setpoint Pressure
2
HPC22 N44:258 * Pack Segment 5 Ram (screw) Pressure Setpoint Pressure
3
HPC23 N44:259 100 Pack Segment 5 Time Setpoint Time
1
HPC24 N44:260 0 Pack Profile Cavity Pressure Offset Pressure
2
HPC25 N44:261 0 Pack Profile Ram (screw) Pressure Offset Pressure
3
HPC26 N44:262 0 Hold Segment 1 Cavity Pressure Setpoint Pressure
2
HPC27 N44:263 * Hold Segment 1 Ram (screw) Pressure Setpoint Pressure
3
HPC28 N44:264 100 Hold Segment 1 Time Setpoint Time
1
HPC29 N44:265 0 Hold Segment 2 Cavity Pressure Setpoint Pressure
2
HPC30 N44:266 * Hold Segment 2 Ram (screw) Pressure Setpoint Pressure
3
HPC31 N44:267 100 Hold Segment 2 Time Setpoint Time
1
HPC32 N44:268 0 Hold Segment 3 Cavity Pressure Setpoint Pressure
2
HPC33 N44:269 * Hold Segment 3 Ram (screw) Pressure Setpoint Pressure
3
HPC34 N44:270 100 Hold Segment 3 Time Setpoint Time
1
HPC35 N44:271 0 Hold Segment 4 Cavity Pressure Setpoint Pressure
2
HPC36 N44:272 * Hold Segment 4 Ram (screw) Pressure Setpoint Pressure
3
HPC37 N44:273 100 Hold Segment 4 Time Setpoint Time
1
HPC38 N44:274 0 Hold Segment 5 Cavity Pressure Setpoint Pressure
2
HPC39 N44:275 * Hold Segment 5 Ram (screw) Pressure Setpoint Pressure
3
HPC40 N44:276 100 Hold Segment 5 Time Setpoint Time
1
HPC41 N44:277 0 Hold Profile Cavity Pressure Offset Pressure
2
HPC42 N44:278 0 Hold Profile Ram (screw) Pressure Offset Pressure
3
HPC61 N44:297 0 Cure Timer Preset Time
4
1
Time
2
Pressure
3
Pressure
4
Time
00.00
to 99.99 seconds 00000 to 20,000 PSI 0000 to 9999 PSI 000.0 to 999.9 seconds
000.0 to2000.0 Bar 000.0 to 999.9 Bar
* Refer to the appropriate section later in this chapter for information on this parameter