Manual

ManualsBrandsRockwell Automation ManualsEquipment1769-IA16 Compact 1769-IA16 120V ac Input Module

Publication 1769-IN006B-EN-P

Compact™ 120V ac Input Module

(Catalog Number 1769-IA16)

Installation Instructions

Inside

Module Description.........................................................................................3

Module Installation..........................................................................................4

System Assembly ...........................................................................................5

Mounting Expansion I/O..................................................................................6

Replacing a Single Module within a System...................................................8

Field Wiring Connections................................................................................8

I/O Memory Mapping....................................................................................11

Spare/Replacement Parts.............................................................................11

Specifications................................................................................................12

Hazardous Location Considerations.............................................................14

Environnements dangereux..........................................................................14

For More Information ....................................................................................15

Summary of content (16 pages)

PAGE 1
Compact™ 120V ac Input Module (Catalog Number 1769-IA16) Installation Instructions Inside Module Description ......................................................................................... 3 Module Installation .......................................................................................... 4 System Assembly ........................................................................................... 5 Mounting Expansion I/O.................................................................
PAGE 2
Publication 1769-IN006B-EN-P
PAGE 3
Module Description Item 1 2a 1 2b lower panel mounting tab DANGER Do Not Remove RTB Under Power Unless Area is Non-Hazardous IN 1 IN 3 bus lever (with locking function) 2a upper panel mounting tab 3 10a Description IN 0 IN 2 IN 4 3 I/O diagnostic LEDs 4 module door with terminal identification label IN 5 IN 6 IN 7 IN 8 10 IN 9 IN 10 IN 11 IN 12 IN 13 IN 14 10b IN 15 AC AC COM COM Ensure Adjacent Bus Lever is Unlatched/Latched Before/After Removing/Inserting Module 5a movable bus c
PAGE 4
Module Installation Compact I/O is suitable for use in an industrial environment when installed in accordance with these instructions. Specifically, this equipment is intended for use in clean, dry environments (Pollution degree 21) and to circuits not exceeding Over Voltage Category II2 (IEC 60664-1).3 Prevent Electrostatic Discharge ! ATTENTION: Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins.
PAGE 5
System Assembly The module can be attached to the controller or an adjacent I/O module before or after mounting. For mounting instructions, see “Panel Mounting” on page 6, or “DIN Rail Mounting” on page 7. To work with a system that is already mounted, see “Replacing a Single Module within a System” on page 8. The following procedure shows you how to assemble the Compact I/O system. 3 4 2 1 6 1 5 1. Disconnect power. 2.
PAGE 6
Mounting Expansion I/O ! ATTENTION: During panel or DIN rail mounting of all devices, be sure that all debris (metal chips, wire strands, etc.) is kept from falling into the module. Debris that falls into the module could cause damage on power up. Minimum Spacing End Cap Compact I/O Compact I/O Compact I/O Controller Side Compact I/O Compact I/O Top Maintain spacing from enclosure walls, wireways, adjacent equipment, etc. Allow 50 mm (2 in.
PAGE 7
Panel Mounting Procedure Using Modules as a Template The following procedure allows you to use the assembled modules as a template for drilling holes in the panel. If you have sophisticated panel mounting equipment, you can use the dimensional template provided on page 6. Due to module mounting hole tolerance, it is important to follow these procedures: 1. On a clean work surface, assemble no more than three modules. 2.
PAGE 8
Replacing a Single Module within a System The module can be replaced while the system is mounted to a panel (or DIN rail). 1. Remove power. See important note on page 4. 2. On the module to be removed, remove the upper and lower mounting screws from the module (or open the DIN latches using a flat-blade or phillips style screw driver). 3. Move the bus lever to the right to disconnect (unlock) the bus. 4.
PAGE 9
Input Wiring Basic wiring1 of input devices to the 1769-IA16 is shown below. ! ATTENTION: Be careful when stripping wires. Wire fragments that fall into a module could cause damage at power up. Once wiring is complete, ensure the module is free of all metal fragments. L1 IN 0 IN 1 IN 2 IN 3 IN 4 IN 5 IN 6 100/120V ac IN 7 IN 8 IN 9 IN 10 IN 11 IN 12 IN 13 IN 14 IN 15 L2 AC COM AC COM Commons are connected internally. A removable, write-on label is provided with the module.
PAGE 10
upper retaining screw wiring the finger-safe terminal block lower retaining screw Removing the Finger-Safe Terminal Block To remove the terminal block, loosen the upper and lower retaining screws. The terminal block will back away from the module as you remove the screws. When replacing the terminal block, torque the retaining screws to 0.46 Nm (4.1 in-lbs). Wiring the Finger-Safe Terminal Block When wiring the terminal block, keep the finger-safe cover in place. 1.
PAGE 11
Wire Size and Terminal Screw Torque Each terminal accepts up to two wires with the following restrictions: Wire Type Wire Size Terminal Screw Torque Retaining Screw Torque Solid Cu-90°C (194°F) #14 to #22 AWG 0.68 Nm (6 in-lbs) 0.46 Nm (4.1 in-lbs) Stranded Cu-90°C (194°F) #16 to #22 AWG 0.68 Nm (6 in-lbs) 0.46 Nm (4.1 in-lbs) I/O Memory Mapping Input Data File For each input module, slot x, word 0 in the input data file contains the current state of the field input points.
PAGE 12
Specifications General Specifications Specification Dimensions Value 118 mm (height) x 87 mm (depth) x 35 mm (width) height including mounting tabs is 138 mm 4.65 in. (height) x 3.43 in (depth) x 1.38 in (width) height including mounting tabs is 5.43 in. Approximate Shipping Weight (with carton) 280g (0.61 lbs.
PAGE 13
Input Specifications Specification 1769-IA16 Voltage Category 100/120V ac Operating Voltage Range 79V ac to 132V ac at 47 Hz to 63 Hz Number of Inputs 16 Bus Current Draw (max.) 115 mA at 5V dc (0.575W) Heat Dissipation 3.30 Total Watts (The Watts per point, plus the minimum Watts, with all points energized.) Signal Delay (max.) On Delay: 20.0 ms Off Delay: 20.0 ms Off-State Voltage (max.) 20V ac Off-State Current (max.) 2.5 mA On-State Voltage (min.
PAGE 14
Hazardous Location Considerations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only. The following ATTENTION statement applies to use in hazardous locations. ATTENTION: EXPLOSION HAZARD ! • Substitution of components may impair suitability for Class I, Division 2. • Do not replace components or disconnect equipment unless power has been switched off or the area is known to be nonhazardous.
PAGE 15
For More Information For A more detailed description of how to install and use your Compact I/O with MicroLogix 1200 & 1500 programmable controller. Refer to this Document MicroLogix 1200 and MicroLogix 1500 Programmable Controllers 1764-RM001B-US-P User Manual A more detailed description of how to 1769-ADN DeviceNet Adapter install and use your Compact I/O with the User Manual 1769-ADN DeviceNet Adapter. More information on proper wiring and grounding techniques. Pub. No.
PAGE 16
Publication 1769-IN006B-EN-P - June 2000 Supercedes 1769-IN006A-EN-P - April 2000 & 1769-5.1 - January 1999 PN 40071-095-01(B) © 2000 Rockwell International Corporation. All rights reserved. Printed in the U.S.A.