Installation Instructions Solid State 24V DC Source Output Module Catalog Number 1762-OB16 Table of Contents Topic Page Additional Resources 2 Description 3 Installation 4 Mounting 5 System Assembly 7 Field Wiring Connections 8 I/O Memory Mapping 10 Specifications 11 North American Hazardous Location Approval 14 Publication 1762-IN011B-EN-P
Solid State 24V DC Source Output Module Additional Resources Publication Description MicroLogix 1200 Programmable Controllers User Information on installing, wiring, and operating a Manual (Bulletin 1762 Controllers and Expansion I/O), MicroLogix 1200 Programmable Controller. publication 1762-UM001. MicroLogix 1200 Programmable Controllers Installation Instructions, publication 1762-IN006. Installation guide for the MicroLogix 1200 Programmable Controller.
Solid State 24V DC Source Output Module 3 Description 9 1a 3 7 6 5 1b 1a 4 2 6 2 8 1b Item Description Item Description 1a upper panel mounting tab 5 bus connector cover 1b lower panel mounting tab 6 flat ribbon cable with bus connector (female pins) 2 I/O diagnostic LEDs 7 terminal block 3 module door with terminal identification label 8 DIN rail latch 4 bus connector with male pins 9 pull loop Publication 1762-IN011B-EN-P - June 2013
Solid State 24V DC Source Output Module Installation 1762 I/O is suitable for use in an industrial environment when installed in accordance with these instructions. Specifically, this equipment is intended for use in clean, dry environments (Pollution degree 2(1)) and to circuits not exceeding Over Voltage Category II(2) (IEC 60664-1).(3) Prevent Electrostatic Discharge ATTENTION Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins.
Solid State 24V DC Source Output Module 5 Mounting Do not remove protective debris strip until after the module and all other equipment near the module is mounted and wiring is complete. Once wiring is complete and the module is free of debris, carefully remove protective debris strip. Failure to remove strip before operating can cause overheating. Minimum Spacing Side MicroLogix 1200 1762 I/O Top 1762 I/O Maintain spacing from enclosure walls, wireways, adjacent equipment, etc. Allow 50.8 mm (2 in.
Solid State 24V DC Source Output Module DIN Rail Mounting The module can be mounted using the following DIN rails: 35 x 7.5 mm (EN 50 022 - 35 x 7.5) or 35 x 15 mm (EN 50 022 - 35 x 15). Before mounting the module on a DIN rail, close the DIN rail latch. Press the DIN rail mounting area of the module against the DIN rail. The latch will momentarily open and lock into place. Use DIN rail end anchors (Allen-Bradley part number 1492-EA35 or 1492-EAH35) for vibration or shock environments.
Solid State 24V DC Source Output Module 7 System Assembly The expansion I/O module is attached to the controller or another I/O module by means of a flat ribbon cable after mounting as shown below. TIP ATTENTION Use the pull loop on the connector to disconnect modules. Do not pull on the ribbon cable. EXPLOSION HAZARD • In Class I, Division 2 applications, the bus connector must be fully seated and the bus connector cover must be snapped in place.
Solid State 24V DC Source Output Module Field Wiring Connections Grounding the Module This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. Refer to Industrial Automation Wiring and Grounding Guidelines, Allen-Bradley publication 1770-4.1, for additional information. Output Wiring Basic wiring(1) of the 1762-OB16 is shown below.
Solid State 24V DC Source Output Module 9 ATTENTION Miswiring of the module to an AC power source will damage the module. TIP Finger-safe cover not shown for clarity. Wiring the Finger-Safe Terminal Block When wiring the terminal block, keep the finger-safe cover in place. 1. Route the wire under the terminal pressure plate. You can use the stripped end of the wire or a spade lug. The terminals will accept a 6.35 mm (0.25 in.) spade lug. 2.
Solid State 24V DC Source Output Module Wire Size and Terminal Screw Torque Each terminal accepts up to two wires with the following restrictions: Wire Type Wire Size Terminal Screw Torque Solid Cu-90 °C (194 °F) #14…22 AWG 0.90 Nm (8 lb-in.) Stranded Cu-90 °C (194 °F) #16…22 AWG 0.90 Nm (8 lb-in.) I/O Memory Mapping Output Data File Word For each output module, the output data file contains the controller-directed state of the discrete output points.
Solid State 24V DC Source Output Module 11 Specifications General Specifications Specification Value Dimensions, HxWxD 90 x 40.4 x 87 mm (height including mounting tabs is 110 mm) 3.54 x 1.59 x 3.43 in. (height including mounting tabs is 4.33 in.) Approximate Shipping Weight (with carton) 235 g (0.52 lbs.
Solid State 24V DC Source Output Module Output Specifications Specification Value Voltage Category 24V DC Operating Voltage Range 20.4…26.4V DC Number of Outputs 16 Bus Current Draw, max 175 mA @ 5V DC (0.88 W) Heat Dissipation max 2.9 total Watts @ 30 °C (86°F) 2.1 total Watts @ 55 °C (131 °F) Signal Delay (max.) – resistive load turn-on = 0.1 ms turn-off = 1.0 ms Off-State Leakage max 1.0 mA On-State Current (min.) 1.0 mA On-State Voltage Drop, max 1.
Solid State 24V DC Source Output Module 13 Certifications Certification (when product is marked)(1) Value c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S and Canada. See UL File E334470. CE European Union 2004/108/EC EMC Directive, compliant with: EN 61326-1; Meas./Control/Lab.
Solid State 24V DC Source Output Module North American Hazardous Location Approval This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only. The following WARNING statement applies to use in hazardous locations.
Solid State 24V DC Source Output Module 15 Notes: Publication 1762-IN011B-EN-P - June 2013
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.
