Programmer (HHP) User guide

(HHP) User Manual
Index
MicroLogix 1000 with Hand-Held Programmer
I–26
First Instruction on Rung, 17–2
home, 4–7
menu, 4–9
mode, 4–10
multi-point function, 4–15
program monitor , 4–1 1
Start of File, 17–1
Start of Rung, 17–2
searching for specific addresses, 17–8
addresses that are displayed, 17–8
addresses you enter , 17–8
bit versus word addresses, 17–9
Selectable T imed Disable (STD), 13–17
entering the instruction, 13–17
example, 13–17
execution times, 13–17
function code, 13–17
instruction parameters, C–9
ladder representation, 13–17
using, 13–17
valid addressing modes, C–9
valid file types, C–9
Selectable T imed Enable (STE), 13–17
entering the instruction, 13–17
example, 13–17
execution times, 13–17
function code, 13–17
instruction parameters, C–9
ladder representation, 13–17
using, 13–17
valid addressing modes, C–9
valid file types, C–9
Selectable T imed Interrupt (STI) function
basic programming procedure, 13–15
Interrupt Subroutine (INT), 13–19
operation, 13–15
interrupt latency and interrupt
occurrences, 13–16
interrupt priorities, 13–16
status file data saved, 13–16
subroutine content, 13–15
overview , 13–15
Selectable T imed Disable (STD), 13–17
Selectable T imed Enable (STE), 13–17
Selectable T imed Start (STS), 13–18
STD/STE zone example, 13–17
Selectable T imed Start (STS), 13–18
entering the instruction, 13–19
execution times, 13–18
function code, 13–19
instruction parameters, C–10
ladder representative, 13–18
valid addressing modes, C–10
valid file types, C–10
Selecting Surge Suppressors, 1–7
selecting the language
using short-cut keys, 4–18
using the menu option, 4–17
Sequencer Compare (SQC), 13–6
entering parameters, 13–6
entering the instruction, 13–10
execution times, 13–6
function code, 13–10
instruction parameters, C–9
ladder representation, 13–6
operation, 13–1 1
using, 13–10
valid addressing modes, C–9
valid file types, C–9
sequencer instructions
overview , 13–6
ef fects on index register S:24, 13–6
entering the instructions, 13–6
Sequencer Compare (SQC), 13–6
Sequencer Load (SQL), 13–12
Sequencer Output (SQO), 13–6
Sequencer Load (SQL), 13–12
entering parameters, 13–12
entering the instruction, 13–13
execution times, 13–12
function code, 13–13
instruction parameters, C–9
ladder representation, 13–12
operation, 13–14
valid addressing modes, C–9
valid file types, C–9
Sequencer Output (SQO), 13–6
entering parameters, 13–6
entering the instruction, 13–8
execution times, 13–6
function code, 13–8
instruction parameters, C–9
ladder representation, 13–6
operation, 13–9
using, 13–7
valid addressing modes, C–9
valid file types, C–9
series logic (AND), 6–12
Set (SET), 8–8
entering the instruction, 8–9
execution times, 8–8
instruction parameters, C–9
ladder representation, 8–8
using, 8–9
valid addressing modes, C–9