Programmer (HHP) User guide

MicroLogix
1000 with Hand-Held Programmer
Index
(HHP) User Manual
I–11
changing
editing modes, 17–3
radix, 18–30
remote controller modes, 18–21, 18–23
the baud rate, 19–6, 19–7
the HHP’
s defaults, 4–17
the language, 4–17
the LCD display contrast, 4–18
the program defaults, 18–1
controller version, 18–18
extended I/O configuration bit, 18–8
fault override bit, 18–7
input filters, 18–12, 18–14, 18–15,
18–16
lock program function, 18–17
program name, 18–2
run always bit, 18–5
start-up protection bit, 18–6
STI enabled bit, 18–10
STI setpoint, 18–9
user and master passwords, 18–2
watchdog scan, 18–1
1
channel configuration
DF1 full–duplex, D–2
DF1 half-duplex slave, D–5
Clear (CLR), 10–1
1
entering the instruction, 10–1
1
execution times, 10–1
1
function code, 10–1
1
instruction parameters, C–3
ladder representative, 10–1
1
updates to arithmetic status bits, 10–1
1
valid addressing modes, C–3
valid file types, C–3
clearing a program
from a memory module, 19–5
from the controller
, 5–2, 19–6
clearing faults, 20–12
CLR, Clear
, 10–1
1
common procedures, 19–1
communication
DeviceNet, 3–13
establishing with controller
, 3–12, 3–13,
19–7
types of, 15–1
communication protocols
DF1 full-duplex, D–2
DF1 half-duplex slave, D–4
DH-485, D–9
comparison instructions, 9–1
about, 9–2
Equal (EQU), 9–3
Greater Than (GR
T), 9–7
Greater Than or Equal (GEQ), 9–8
Less Than (LES), 9–5
Less Than or Equal (LEQ), 9–6
Limit T
est (LIM), 9–10
Masked Comparison for Equal (MEQ), 9–9
Not Equal (NEQ), 9–4
overview
, 9–2
entering the instruction, 9–2
function codes, 9–3
using indexed word addresses, 9–3
configuring your program, 18–1
controller version, 18–18
extended I/O configuration, 18–8
fault override bit, 18–7
input filter settings, 18–12, 18–14, 18–15,
18–16
lock program function, 18–17
program name, 18–2
run always bit, 18–5
start-up protection, 18–6
STI enabled bit, 18–10
STI setpoint, 18–9
user and master passwords, 18–2
watchdog scan, 18–1
1
connecting blocks of logic
using ANB, 6–14, 8–12, 16–2
using ORB, 6–14, 8–12, 16–3
connecting the system
AIC+, 3–6
DeviceNet network, 3–13
DH-485 network, 3–3
HHP
, 3–1
contact protection methods, 1–7
contacting Allen-Bradley for assistance, P–6
contactors (bulletin 100), surge suppressors
for
, 1–9
contents of manual, P–2
continuous scan (CSN) mode, 18–22
control file (R), 6–4
controller
accessories and replacement parts, A–1
1
changing modes, 18–21
changing the baud rate, 19–6, 19–7
determining faults, 20–1
dimensions, A–7
fault messages, 20–13
features, 1–2
grounding, 2–1
installation, 1–1
mounting, 1–12