Programmer (HHP) User guide

(HHP) User Manual
T able of Contents
MicroLogix 1000 with Hand–Held Programmer
toc–v
Selectable T imed Disable (STD) and Enable (STE) 13–17. . . . . . . . . . . . . . . . . . .
Selectable
T imed Start (STS) 13–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Subroutine (INT) 13–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application
Specific Instructions in the Paper Drilling Machine
Application Example 13–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 14
About the High-Speed Counter Instructions 14–1. . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Instructions Overview 14–2. . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter (HSC) 14–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Load (HSL) 14–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Reset (RES) 14–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Reset Accumulator (RAC) 14–20. . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Interrupt Enable (HSE) and Disable (HSD) 14–21. . . . . . . . . .
Update High-Speed Counter Image Accumulator (OUT) 14–23. . . . . . . . . . . . . . . .
What
Happens to the HSC When Going to RRUN Mode 14–23. . . . . . . . . . . . . . . .
High-Speed
Counter Instructions in the Paper Drilling Machine
Application Example
14–28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 15
Types of Communication 15–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message
Instruction (MSG) 15–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing
Diagram for a Successful MSG Instruction 15–9. . . . . . . . . . . . . . . . . . . .
MSG Instruction Error Codes 15–11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application
Examples that Use the MSG Instruction 15–12. . . . . . . . . . . . . . . . . . .
Chapter 16
Programming Examples 16–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Considerations 16–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 17
Entering the Program Monitor 17–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Considerations 17–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Modes 17–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting Instructions and Rungs 17–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching for Specific Addresses 17–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using High–Speed Counter
Instructions
Using Communication
Protocols
Instruction List Programming
Concepts
Entering and Editing Y our
Program