Installation Instructions ProcessLogix Remote Termination Panel (RTP) (Catalog Number 1757-FIMRTP) For information about: See Page: Important User Information 2 Installing the 1757-FIMRTP 4 Wiring the RTP 6 Hazardous Locations 9 Specifications 10 Package Contents: • 1 remote termination panel (1757-FIMRTP) screws, washers and standoffs pre-assembled • 2 DIN rail mounting brackets • installation instructions • instruction sheet Publication 1757-IN915A-EN-P - October 2001
ProcessLogix Remote Termination Panel (RTP) Important User Information Because of the variety of uses for the products described in this publication, those responsible for the application and use of these products must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards.
ProcessLogix Remote Termination Panel (RTP) ATTENTION ! 3 Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 meters without derating. This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR Publication 11.
ProcessLogix Remote Termination Panel (RTP) Installing the 1757-FIMRTP Mount the RTP onto a DIN Rail Use the enclosed instruction sheet to attach the brackets and mount the RTP onto a DIN rail. Mount the RTP with Optional Enclosure onto a DIN Rail Follow these steps to attach the brackets and enclosure, then mount the RTP onto a DIN rail: 1. Replace the screws on the RTP with the longer screws shipped with the enclosure. 2.
ProcessLogix Remote Termination Panel (RTP) 5 Mounting Dimensions Reference: Inches Millimeters Hole Size: 0.156 3.96 0.425 10.8 5.6 142.2 RT P CABLE J4 J6 J1 4.75 120.7 14 J8 J3 7 7 4.10 104.2 6 152.4 J7 FB- SEGMENT #2 FB+ FB- SHIELD 1 J5 FB+ J2 FB- SEGMENT #1 FB+ FB- SHIELD 1 FB+ 14 J10 J9 0.225 5.
ProcessLogix Remote Termination Panel (RTP) Wiring the RTP WARNING ! When you connect or disconnect the RTP with field side power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. Use the following procedure and the wiring diagram, on page 7, to make wiring connections to the RTP: 1.
ProcessLogix Remote Termination Panel (RTP) 7 Wiring Diagram for the RTP Field Wiring Fieldbus 1757-FIMRTP 14 13 12 11 10 9 8 7 Segment 1 FB+ T Field Devices HHC J2 J7 HHC 1 2 FB- 3 4 5 SHIELD 6 FB+ FB- J1 2.2 uF IMU FB+ Field Devices 10 Ohm J5 14 13 12 11 10 9 8 7 Segment 2 T 1 JP1 J3 1 2 FB- 3 4 5 SHIELD 6 FB+ FB- 1757-FIM J9 J8 JP 2 10 Ohm J1 2.
ProcessLogix Remote Termination Panel (RTP) Connecting the RTP to the FIM This procedure assumes that the 1757-FIM is installed. Use the following procedure to connect the RTP cable to the FIM: 1. Turn off the power supply in the chassis. WARNING ! When you connect or disconnect any wiring to the FIM with power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. 2.
ProcessLogix Remote Termination Panel (RTP) 9 Hazardous Locations The following information applies when operating this equipment in hazardous locations: Informations sur l’utilisation de cet équipement en environnements dangereux: Products marked “CL I, DIV 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code.
ProcessLogix Remote Termination Panel (RTP) Specifications 1757-FIMRTP Specifications RTP Maximum Power Requirements None Fieldbus Current Available per Link Limited by user-supplied power Terminators per Link None H1 Terminal Connection Type Compression RTP Dimensions 4.9" W x 6.
ProcessLogix Remote Termination Panel (RTP) 11 Notes: Publication 1757-IN915A-EN-P - October 2001
Allen-Bradley and ProcessLogix are Trademarks of Rockwell Automation. Foundation Fieldbus is a trademark of the Fieldbus Foundation. Publication 1757-IN915A-EN-P - October 2001 PN 957603-49 © 2001 Rockwell International Corporation. Printed in the U.S.A.
