Installation Instructions User Manual

ManualsBrandsRockwell Automation ManualsEquipment1756-Mx ControlLogix Memory Board

Publication 1756-IN033B-EN-P - November 2000

Installation Instructions

ControlLogix™ Memory Board

Catalog Number: 1756-M1, -M2, -M3, -M13, -M14, -M16

Before You Begin

Use this document as a guide to install your ControlLogix memory board. The

memory board privides additional memory for your ControlLogix controller. You

can install only one memory board per controller.

Additional Manuals

This product has the following manuals:

• Logix5000 Controllers Common Procedures Programming Manual,

publication 1756-PM001

• ControlLogix System User Manual, publication 1756-UM001

If you want to:

• view or download a manual, visit either of these locations:

– www.ab.com/manuals

– www.theautomationbookstore.com

• purchase a printed manual, use one of these options:

– contact your local distributor or Rockwell Automation representative

– visit www.theautomationbookstore.com and place an order

– call 800.963.9548 (USA/Canada) or 001.320.725.1574 (outside

USA/Canada)

Tools that You Need

• #2 phillips screwdriver

• grounding wriststrap

Summary of content (16 pages)

PAGE 1
Installation Instructions ControlLogix™ Memory Board Catalog Number: 1756-M1, -M2, -M3, -M13, -M14, -M16 Before You Begin Use this document as a guide to install your ControlLogix memory board. The memory board privides additional memory for your ControlLogix controller. You can install only one memory board per controller.
PAGE 2
ControlLogix™ Memory Board Important User Information Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards.
PAGE 3
ControlLogix™ Memory Board 3 European Communities (EC) Directive Compliance If this product has the CE mark it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives.
PAGE 4
ControlLogix™ Memory Board What You Need to Do To guard against ESD damage, take these precautions: ATTENTION ! Electrostatic discharge can damage the components.
PAGE 5
ControlLogix™ Memory Board 5 Step 1: Verify that You Have All the Components A. Locate the following components: Component: Description: memory board 40042 memory board label catalog number labels 1756-L1 1756-L1M1 The catalog numbers on your labels may be different from the ones that are shown. 1756-L1M2 B.
PAGE 6
ControlLogix™ Memory Board Step 2: Remove the Controller from the Chassis You can install or remove a ControlLogix controller while chassis power is applied and the system is operating. If you remove the controller, all the devices owned by the controller go to their configured faulted state. WARNING ! When you insert or remove a module while backplane power is on, an electrical arc may occur.
PAGE 7
ControlLogix™ Memory Board 7 Step 3: Remove the Side Plate of the Controller A. Lay the controller on its side with the label facing up. B. While wearing a grounding wriststrap, remove the two screws that attach the side plate to the controller. C. Rotate the side plate up and unhook it from the controller.
PAGE 8
ControlLogix™ Memory Board Step 4: Remove the Existing Memory Board (If Any) memory board 42527 Does the controller already have a memory board? If: Then: No Go to Step 5: Install the Memory Board Yes Remove the existing memory board: 1. Pull the plastic back edge of the controller out slightly to clear the tabs on the memory board. tab tab 42526 2. Gently separate and remove the memory board from the controller.
PAGE 9
ControlLogix™ Memory Board 9 Step 5: Install the Memory Board memory board tab tab slot slot 40018 A. Place the memory board over the connector and slide the memory board into the controller. B. Pull the plastic back edge of the controller out slightly to clear the tabs of the memory board. C. Line up the connectors. D. Place your hands on the boards over the connectors and gently squeeze them together. E.
PAGE 10
ControlLogix™ Memory Board Step 6: Replace the Side Plate side plate 40019 A. Line up the hinge tabs on the side plate with the slots in the plastic housing of the controller. B. Gently press the side plate against the controller. C. Replace the screws.
PAGE 11
ControlLogix™ Memory Board 11 Step 7: Attach Labels A. 40019 A. Place the memory board label on the side of the controller. It identifies which memory board is installed. B. From the sheet of catalog labels, peel off the label that corresponds to the memory board that you installed. (E.g., If you installed an M2 memory board, peel off the 1756-L1M2 label.) 1756-L1 1756-L1M1 1756-L1M2 identifies the memory board 1756-LxMx 41025 C. Place the catalog number label on the inside of the controller door.
PAGE 12
ControlLogix™ Memory Board Agency Certifications When marked, the controller and memory board have the following certifications: This component: Has these certifications (when the product is marked): 1756-L1 controller 1756-L55 controller Listed Industrial Control Equipment Certified Process Control Equipment Certified Class I, Division 2, Group A, B, C, D Marked for all applicable directives Marked for all applicable acts N223 1756-Mx memory board UL Recognized Component Industrial Control Equipm
PAGE 13
ControlLogix™ Memory Board 13 Specifications Table A 1756-L1, -L1Mx Controller Description: user available memory Value: (1) peak backplane current +5V dc +24V dc 1756-L1 1756-L1M1 1756-L1M2 1756-L1M3 64K bytes 512K bytes 1M bytes 2M bytes 0.65A 0.02A 0.95A 0.02A 1.05A 0.02A 1.20A 0.02A average power dissipation 3.3W 4.6W 4.8W 5.4W average thermal dissipation 11.3 BTU/hr 15.6 BTU/hr 16.4 BTU/hr 18.
PAGE 14
ControlLogix™ Memory Board Table B 1756-L55Mxx Controller Description: Value: 1756-L55M13 1756-L55M14 1756-L55M16 user available memory(1) 1.5M bytes 3.5M bytes 7.5M bytes peak backplane current +5V dc +24V dc 1.23A 0.014A 1.25A 0.014A 1.48A 0.014A average power dissipation 5.6W 5.7W 6.3W average thermal dissipation 19.1 BTU/hr 19.4 BTU/hr 21.
PAGE 15
ControlLogix™ Memory Board 15 Hazardous Location information The following information applies when operating this equipment in hazardous locations: Products marked “CL I, DIV 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code.
PAGE 16
Informations sur l’utilisation de cet équipement en environnements dangereux : Les produits marqués « CL I, DIV 2, GP A, B, C, D » ne conviennent qu’à une utilisation en environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livré avec des marquages sur sa plaque d’identification qui indiquent le code de température pour les environnements dangereux.