Instruction Manual

ManualsBrandsRockwell Automation ManualsEquipment1747-PCIS2 PCI Bus Card

Installation Instructions

Publication 1747-5.31–April 1998

PCI Bus Card for 1746 Local I/O

(Catalog Numbers 1747-PCIS/PCIS2)

Use this document to install and configure the Peripheral Component

Interface (PCI) Bus card for 1746 Local I/O in your personal computer

and connect the card to a Chassis Interface module (1747-PCIL) for

1746 Local I/O. The PCI Bus card works with the Chassis Interface

module and a connecting cable to make up the 1747 PCI Bus Interface.

For additional information on the installation and use of the Chassis

Interface module, see publication 1747-5.32.

In the instructional text of this document, we refer to the PCI Bus card

as the scanner and the Chassis Interface module as the adapter.

We use these conventions in this document:

To install the card, read:

See page:

Compliance to European Union Directives

Verify Package Contents

Installing the Battery and its Connecting Jumper

User SRAM

Setting the Jumper for Battery Back-Up

Setting the Base Memory Address Jumper

Accessing the Computer’s PCI Bus Slots

Installing the Scanner

Selecting the Cable for Your Connections

Connecting the Scanner to the Adapter

General Operation

Calculating Scan Time

Troubleshooting

Specifications

Convention Shows

9 pt Courier bold Text you type as shown at the DOS prompt

Summary of content (12 pages)

PAGE 1
Installation Instructions PCI Bus Card for 1746 Local I/O (Catalog Numbers 1747-PCIS/PCIS2) Use this document to install and configure the Peripheral Component Interface (PCI) Bus card for 1746 Local I/O in your personal computer and connect the card to a Chassis Interface module (1747-PCIL) for 1746 Local I/O. The PCI Bus card works with the Chassis Interface module and a connecting cable to make up the 1747 PCI Bus Interface.
PAGE 2
PCI Bus Card for 1746 Local I/O Compliance to European Union Directives If this product bears the CE marking, it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives.
PAGE 3
PCI Bus Card for 1746 Local I/O Verify Package Contents Make sure that you have these items before you discard any packing material. If an item is missing or incorrect, contact your local sales representative. PCI Bus card Installation instructions (Publication 1747-5.31) 3.5” Software Utility disk Jumper for Battery Back-up PCI Bus card battery Battery Base Memory Address Jumper 30578-M Installing the Battery and its Connecting Jumper A battery has been included for your scanner.
PAGE 4
PCI Bus Card for 1746 Local I/O User SRAM 256K (1747-PCIS) or 1M (1747-PCIS2) battery backed-up SRAM exists on the scanner to be used by the host CPU. The host application defines the SRAM’s function. For additional information on access and use of the user SRAM when using the API software, see 1747 PCI Bus Interface for 1746 Local I/O API Software user manual, publication 1747-6.5.3. If you are using another software application, refer to the documentation for that software.
PAGE 5
PCI Bus Card for 1746 Local I/O 5 Setting the Base Memory Address Jumper The host computer and the PCI Bus card exchange data via a dual-port interface. The dual-port requires 4 Kbytes of memory. This 4 Kbyte block of memory begins at the base memory address assigned to the card by the PCI BIOS when the computer is started. Under MS-DOS, Windows 3.1 and Windows for Workgroups, the base memory address of PC cards should fall within the range of 0 and 1 Megabyte of PC memory.
PAGE 6
PCI Bus Card for 1746 Local I/O Accessing the Computer’s PCI Bus Slots To install the scanner, you must have access to the computer’s PCI bus. Refer to your computer’s hardware manual for instructions about how to: 1. Shut down the computer’s operating system. 2. Turn off power to the computer. Important: If you disconnect the ac power from the computer, you lose the chassis ground. Electrostatic damage (ESD) protection is lost. 3.
PAGE 7
PCI Bus Card for 1746 Local I/O Installing the Scanner To install the scanner inside the computer: 1. Turn off power to the computer. Important: If you disconnect the ac power from the computer, you lose the chassis ground. Electrostatic damage (ESD) protection is lost. 2. Loosen the expansion slot screw and remove the outside retaining bracket. 3. Insert the scanner into the edge connector and tighten the expansion slot screw on the scanner outside retaining bracket. 4. Restore power to the computer. 5.
PAGE 8
PCI Bus Card for 1746 Local I/O Connecting the Scanner to the Adapter To connect the scanner to the adapter, you must: 1. Connect one end of the 1747-PCIC cable to the scanner. 2. Connect the other end of the 1747-PCIC cable to the adapter. Either end of cable can connect to either the scanner or adapter.
PAGE 9
PCI Bus Card for 1746 Local I/O 9 General Operation The scanner is a PCI Bus card that is installed in a PC. It scans 1746 I/O modules via the 1747-PCIC cable and adapter. The scanner can communicate to any 1746 I/O module. The application program on the PC will provide the software driver to initialize and control the scanner. Once the scanner is running, it continuously retrieves all the input data from the 1746 I/O modules and places the data in dual port memory on board the scanner.
PAGE 10
PCI Bus Card for 1746 Local I/O Estimate Maximum Input Scan Time Quantity Fixed Scan Time Total Minimum Input Scan Time (from previous table) Maximum Specialty I/O Input Scan Time number of class 1 specialty I/O modules: number of class 3 and 4 specialty I/O modules: X 50 = X 200 = Maximum Input Scan Time (total) Estimate Minimum Output Scan Time Quantity Fixed Scan Time Digital I/O Modules: number of class 0 input words: X 46 = Specialty I/O Modules (Class 1) number of 1746-BAS modules (clas
PAGE 11
PCI Bus Card for 1746 Local I/O 11 Estimate Maximum Output Scan Time Quantity Fixed Scan Time Total Minimum Input Scan Time (from above table) Maximum Specialty I/O Output Scan Time number of class 1 specialty I/O modules: number of class 3 and 4 specialty I/O modules: X 50 = X 200 = Maximum Output Scan Time (total) Estimate Output Scan Time Plus Processor Overhead Minimum or Maximum Output Scan Time (from previous tables) Overhead if DII Enabled 60 Processor Overhead minimum = 140 maximum = 200
PAGE 12
PCI Bus Card for 1746 Local I/O Specifications Operational Slot Temperature 0 to 60o Non-operational Slot Temperature -40 to 85o Relative Humidity 5-95% without condensation Vibration 10-60Hz 60-150Hz Constant 0.012 in displacement Constant 2.