Installation Instructions 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Catalog number 1738-AENTR, Series B Table of Contents Topic Page Important User Information 2 Environment and Enclosure 3 Preventing Electrostatic Discharge 3 Additional Resources 4 About The Adapter 5 Before You Begin 6 Determine Compatibility 6 Understand Messaging 6 Configure Autobaud 6 Mount the Adapter and I/O Base 7 Set the Network Address 9 Set the Network Address 9 Wire The Adapter 10 Interpret S
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 3 Environment and Enclosure ATTENTION: This equipment is intended for use in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments. This equipment is supplied as enclosed equipment.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Additional Resources Resource Description 1734 POINT I/O® and 1738 ArmorPOINT I/O® Dual Port EtherNet/IP Adapter User Manual, publication 1734-UM017. A detailed description of module functionality, configuration, installation procedures and information on how to use POINT I/O and ArmorPOINT I/O Dual Port EtherNet/IP adapters (1734-AENTR, Series B and 1738-AENTR, Series B).
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 5 About The Adapter The Series B 1738-AENTR ArmorPOINT I/O Dual Port EtherNet/IP Adapter provides connectivity to an EtherNet/IP network via two M12 EtherNet-keyed connectors for 2-port pass-through to support daisy chains or rings, and the existing star and tree network topologies. The adapter ships with a terminating base to be used with the last I/O module on the backplane.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Before You Begin To effectively use your adapter, note the following considerations. Determine Compatibility RSLogix™ 5000 version 17 or greater must be used for the 1738-AENTR Add-on Profile. The 1738-AENTR adapters will accept I/O connections with electronic keying for the 1738-AENT. This allows the 1738-AENTR adapter to be used in a daisy-chain topology with the 1738-AENT profile used for the 1738-AENTR.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 7 Mount the Adapter and I/O Base To mount the ArmorPOINT I/O adapter on a wall or panel, use the screw holes provided in the adapter. A mounting illustration for the ArmorPOINT adapter with several attached I/O bases is shown below. ATTENTION: This product is intended to be mounted to a well-grounded mounting surface such as a metal panel.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 4. Ground the system using the ground lug connection in the adapter’s I/O base. (The ground lug connection is also a mounting hole). 5. Add one or more I/O modules and their respective I/O mounting bases to the adapter and its I/O Mounting base as required. See Set the Network Address on page 9 for details. 6.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 9 Set the Network Address The adapter ships with the rotary network address switches set to 999 and DHCP enabled. To change the network address, you can: • adjust the switches on the front of the module • use a Dynamic Host Configuration Protocol (DHCP) server, such as Rockwell Automation BootP/DHCP. • retrieve the IP address from nonvolatile memory The adapter reads the switches first to determine if the switches are set to a valid number.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Wire The Adapter Following are the wiring instructions for the adapter.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 11 Interpret Status Indicators Refer to the following diagram and table for information on how to interpret the status indicators.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Indicator Status for Modules Indicator State Description Network Activity Off No link established with Port 1 or Port 2. Flashing green Transmit or receive activity present on Port 1 and/or Port 2 @ 100 Mbps. Transmit or receive activity present on Port 1 and/or Port 2. One port @ 100 Mbps and one port @ 10 Mbps. Solid green Link established with Port 1 and/or Port 2 @ 100 Mbps. Link established with Port 1 and Port 2.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 13 Specifications ArmorPOINT I/O EtherNet/IP Adapter — 1738-AENTR, Series B Attribute Value Expansion I/O capacity, max • 63 modules • 5 rack-optimized connections (for digital modules only) • 31 direct connections • 1738-AENTR backplane current output = 0.8 A. • Actual number of modules can vary. • Add up current requirements of modules you want to use to make sure they do not exceed the amperage limit of 0.8 A for the 1738-AENTR adapter.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Power Supply Attribute Value Inrush current, max 6 A for 10 ms Input overvoltage protection Reverse polarity protected POINTBus output current, max 5V DC @ 0.8A Auxiliary power cable(1) Standard cordset (single-ended), for example Allen-Bradley part number 889N-F4AFC-6F or 889N-R4AFC-6F. Standard patchcord (double-ended), for example, Allen-Bradley part number 889N-F4AFNU-6F or 889N-F4AFNV-6F.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 15 General Specifications Attribute Value Input overvoltage protection Reverse polarity protected Thermal dissipation, max 21.5 BTU/hr @ 28.8V DC Isolation voltage 50V (continuous), Basic Insulation Type. Type Tested @ 500V AC for 60 s: • Comm to system • Comm to user power • User power to system • User power to ground • System to ground Field power supply 10...28.8V DC @ 10A Field power output 10...28.8V DC @ 9A Module input 10...
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Environmental Specifications Attribute Value Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat): 5...95% noncondensing Vibration IEC 60068-2-6 (Test Fc, Operating): 5 g @ 10...
38 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 17 Certifications Certification (when product is marked)(1) Value c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E322657. CE European Union 2004/108/EC EMC Directive, compliant with: EN 61326-1; Meas./Control/Lab.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Notes: Publication 1738-IN030A-EN-P - July 2013
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 19 Notes: Publication 1738-IN030A-EN-P - July 2013
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.
