Configuration User Manual

Rockwell Automation Publication ENET-UM001L-EN-P - March 2014 5
Table of Contents
Preface About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Studio 5000 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 1
EtherNet/IP Overview
EtherNet/IP Communication Modules in a Control System. . . . . . . . . 11
Chapter 2
Configure a Workstation to Operate
on an EtherNet/IP Network
Configure the Ethernet Communication Driver in RSLinx Software . 14
Chapter 3
Configure an EtherNet/IP
Communication Module to Operate
on the Network
Determine Network Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Set the Network IP Address on a Module . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Set the Network IP Address with the Rotary Switches . . . . . . . . . . . 20
Set the Network IP Address with the BOOTP/DHCP Server. . . . 21
Set the Network IP Address with RSLinx Software or the
Studio 5000 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Reset the Module IP Address to Factory Default Value . . . . . . . . . . 29
Duplicate IP Address Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Duplicate IP Address Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IP Address Swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DNS Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Use EtherNet/IP Communication Modules in a Logix5000
Controller Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 4
Configure a Supervisor on a Device-
level Ring Network
DLR Nodes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Supervisor Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ring Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Construct the Physical Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Configure Supervisor Nodes on a DLR Network . . . . . . . . . . . . . . . . . . . 37
Configure a Ring Supervisor in the Studio 5000 Environment. . . . 37
Enable Ring Supervisor in the Studio 5000 Environment . . . . . . . . 40
Configure and Enable a Ring Supervisor in RSLinx
Classic Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Complete the Physical Connections of the Network . . . . . . . . . . . . . . . . 45
Verify Supervisor Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46