60 SSC™ Variable Speed Drive (Series C) Publication 160-CDP Configured Drive Package
Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature) describes some important differences between solid state equipment and hard-wired electromechanical devices.
Bulletin 160 SSC™ Variable Speed Controller Configured Drives Package Thank you for purchasing a Bulletin 160 Configured Drive. This Rockwell Automation product is designed with the customer in mind, saving time and money by configuring a drive package at the factory to meet your application needs. This publication contains all drawings for the Bulletin 160 Configured Drive product offering.
Table of Contents Data Nameplate Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 (Use for all catalog numbers.) Standard Control Interface for Analog Signal Follower and Preset Speed Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 (Use when drive catalog number does not include control interface options DMSF1C, DMPS1C, or LTN120.
Data Nameplate Drawing A B C D E F G H 1 1 2 3 DATA NAMEPLATE CAT. NO. 4 SEE_NOTE_2 -SERIES_C 5 SEE_NOTE_3 H.P. TABLE_1 ENCLOSURE TYPE 6 AMPS TABLE_1 LISTED 966X IND.CONT.EQ. 1S FACILITY US SER. NO. SEE_NOTE_3 H.P.
Standard Control Interface (Drawing C-300356-2) Power Distribution and DS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Operator Interface Options DN2C, RS1C, P1C, RPAC, P2C, and Ready/Fault Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Enclosure Mounted DeviceNet Connector Options: DNSC1, DNSC2, DNBC1, DNBC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Distribution and DS Option A B C D E F G H 1 1 BRAKE 1C 2 2 L2 * 1PH, 50/60HZ AC LINES 3 4 L1 5 1 DISCONNECTING MEANS AND SHORT CIRCUIT PROTECTION PROVIDED BY OTHERS WHEN DS OPTION IS NOT ORDERED L2 6 3PH, 50/60HZ AC LINES 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 3 L3 17-18 17-37 L3 4 LINE FILTER 2 4 5 MX14 OPTION 5 6 MODULE 6 3 7 LINE PE 8 POWER DISCONNECTING OPTION 9 DS OPTION 10 CHASSIS EA1 GRD R S TERMINAL BLOCK TB1 E
Drive Ratings and DS Option Ratings A B C D E F G H 1 1 TABLE 1 2 2 SINGLE PHASE 3 DRIVE RATINGS CATALOG NO. VOLTAGE (HP) FLA 4 3 LINE FILTER MODULE CATALOG NUMBER FUSE RATINGS (DS OPTION) TYPE AMP VOLT 5 160S-AA02* (.5) 160S-AA03* (.75) 160S-AA04* (1) 160S-AA08* (2) 6 200-240V 200-240V 200-240V 200-240V LPJ LPJ LPJ LPJ 2.3A 3.0A 4.5A 8.
D13 Without P2C A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND 10 5 RUN REVERSE 6 RUN FORWARD AUTO 20 (3) (XOO) (4) 11 21 12 (3) (4) (OOX) 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONTROL 13 14 22 SS2 15 9 16 17 17 PROGRAMMABLE RELAY OUTPUTS 1
D13 With P2C A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND AUTO 20 (3) (OOX) 10 5 RUN REVERSE 6 RUN FORWARD 2-WIRE DEVICE 11 (4) 12 * (3) (4) (XOO) 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONTROL 13 14 22 SS2 15 9 16 17 17 PROGRAMMABLE RELAY
D17 A B 3 COMMON 26 4 SW3 01-19-07 ARS ARS DATE ACAD 02-09-99 WTG 02-09-99 BAH 02-09-99 WS\STD\300356\02-05 INDEX NO. L\DM\1336P?? REFERENCE DWG. DATE APP'D DATE LEAD ENG. 28 ECN NUMBER 27 99P0068 99P0562 DR. 25 1026630 SW2 BY TITLE: DWG. NO.
D32 A B C 3 COMMON 26 4 SW3 01-19-07 ARS ARS DATE ACAD 02-09-99 WTG 02-09-99 BAH 02-09-99 WS\STD\300356\02-06 INDEX NO. L\DM\1336P?? REFERENCE DWG. DATE APP'D DATE LEAD ENG. 28 ECN NUMBER 27 99P0068 99P0562 DR. 25 1026630 SW2 BY TITLE: DWG. NO. 38 C-300356-2 SCHEMATIC, BULLETIN 160 AC DRIVE SERIES C CONTROL LOGIC OPTION D32 PROJECT: DRIVE 11 37 (PAR 46 = 0) 38 D 03 12-17-99 27 2 WTG 10 23 160 CONTROL BOARD THIS DRAWING IS THE PROPERTY OF ROCKWELL AUTOMATION, INC.
D33 A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 10 5 RUN REVERSE 6 RUN FORWARD 2-WIRE DEVICE 11 12 * LOCAL 20 (3) (OX) REMOTE 22 (4) 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONTROL 13 14 SS1 15 9 16 17 17 PROGRAMMABLE RELAY OUTPUTS 10 18 INPUT MODE 6
D13 and D32 Without P2C A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 OFF HAND AUTO FORWARD 20 (3) (XOO) (4) 21 (3) (OX) (1) (3) (4) 10 5 RUN REVERSE 6 RUN FORWARD 11 24 SS3 (XO) (OOX) (2) 9 TERMINAL BLOCK TB3 REVERSE 23 (4) 12 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONT
D13 and D32 With P2C A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 AUTO CONTROL OFF HAND AUTO 20 (3) (OOX) (4) 2-WIRE DEVICE 21 FORWARD 23 (3) (OX) 9 TERMINAL BLOCK TB3 REVERSE 24 (4) 10 5 RUN REVERSE 6 RUN FORWARD * (1) (XO) (2) 11 25 SS3 12 7 COMMON 8 TB3/KEYPAD OR COMMU
D17 and D32 A B C 23 160 CONTROL BOARD 03 12-17-99 01-19-07 27 25 3 COMMON 26 4 SW3 ARS ARS BY WTG DATE ACAD 02-09-99 WTG 02-09-99 BAH 02-09-99 WS\STD\300356\02-10 INDEX NO. L\DM\1336P?? REFERENCE DWG. DATE APP'D DATE LEAD ENG. 28 ECN NUMBER 27 99P0068 99P0562 DR. SW2 1026630 2 THIS DRAWING IS THE PROPERTY OF ROCKWELL AUTOMATION, INC. OR ITS SUBSIDIARIES AND MAY NOT BE COPIED, USED OR DISCLOSED FOR ANY PURPOSE EXCEPT AS AUTHORIZED IN WRITING BY ROCKWELL AUTOMATION, INC.
D32 and D33 A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 2-WIRE DEVICE FORWARD 21 (3) 9 TERMINAL BLOCK TB3 REVERSE 23 (4) (OX) 10 5 RUN REVERSE 6 RUN FORWARD * (1) 11 24 SS3 (XO) LOCAL 20 (3) (OX) (2) 12 REMOTE 22 (4) 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONTROL 13 14
D35 and D36 Without Keypad or Comm Control Options A B C D E F G H 1 1 2 2 TABLE 2 3 OPTION SYMBOL COLOR LEGEND PAR 47 SETTING 4 D35 D36 PL3 PL4 WHITE RED DRIVE RUN DRIVE FAULT 2 0 (DEFAULT) 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 5 REVERSE 6 START 10 START 20 11 21 * 12 7 COMM
D35 and D36 With Keypad or Comm Control Options A B C D E F G H 1 1 2 2 TABLE 2 3 OPTION SYMBOL COLOR LEGEND PAR 47 SETTING 4 D35 D36 PL3 PL4 WHITE RED DRIVE RUN DRIVE FAULT 2 0 (DEFAULT) 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND AUTO 10 5 RUN REVERSE 6 RUN FORWARD 2-WIRE
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options 17 PROGRAMMABLE RELAY OUTPUTS 17 10 A B DR. DATE LEAD ENG. DATE APP'D DATE ACAD 02-02-99 WTG 02-09-99 BAH 02-02-99 REFERENCE DWG. TITLE: DWG. NO.
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options 10 A B DR. DATE LEAD ENG. DATE APP'D WIRE TB3-7 TO TB3-8 IF OPTIONS D13, D33 OR MX12 ARE NOT ORDERED. ACAD 02-02-99 WTG 02-09-99 BAH 02-02-99 L\DM\1336P?? REFERENCE DWG. DATE NOTE 1: WS\STD\300356\02-15 INDEX NO. TITLE: DWG. NO.
MX12 A B C D E F G H 1 1 2 2 3 3 ANALOG SIGNAL FOLLOWER 4 4 160 CONTROL BOARD TB3 1 +10V POT 5 6 2 WIPER/0-10VDC INPUT 6 7 3 COMMON 7 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 LOCAL CONTROL OFF RUN FWD 20 (B)A1 21 (B)A2 R (OX) SS2 LOCAL 20 (B)A1 (OX) RUN REVERSE 6 RUN FORWARD 10 11 12 REMOTE 22 (B)A2 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONTROL 13 14 R SS1 5 15 9 16 17 17 PROGR
MX14 A B C D E F G H 1 1 2 4 5 6 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 +10V POT 2 WIPER/0-10VDC INPUT 3 COMMON 4 4-20mA INPUT 5 RUN REVERSE 6 RUN FORWARD 7 COMMON 8 TB3/KEYPAD OR COMMUNICATION CONTROL 4 6 LOCAL (OX) 12 14 9 31 15 PROGRAMMABLE RELAY OUTPUTS 10 16 INPUT MODE 6 1C 32 30 A1 17 (PAR 46 = 6) 11 18 1-2 1-3 19 MX14 OPTION 20 03 02-18-00 06-16-00 THIS DRAWING IS THE PROPERTY OF ROCKWELL AUTOMATION, INC.
P2C 3 COMMON 26 4 SW3 ARS BY 28 ACAD 11-18-99 ARS 11-18-99 BAH 11-18-99 ECN NUMBER WS\STD\300356\02-18 INDEX NO. 27 99P0562 L\DM\1336P?? REFERENCE DWG. DATE APP'D DATE LEAD ENG. DATE DR. 25 01P0009 SW2 ARS NO. DWG. TITLE: RUN FORWARD A B C D E 01-19-01 27 2 THIS DRAWING IS THE PROPERTY OF ROCKWELL AUTOMATION, INC. OR ITS SUBSIDIARIES AND MAY NOT BE COPIED, USED OR DISCLOSED FOR ANY PURPOSE EXCEPT AS AUTHORIZED IN WRITING BY ROCKWELL AUTOMATION, INC.
MX19 A B C D E F G H 1 1 2 2 ANALOG SIGNAL FOLLOWER 3 4 3 160 CONTROL BOARD TB3 1 +10V POT 2 WIPER/0-10VDC INPUT 3 COMMON 4 5 5 6 6 OFF 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN LOCAL 8 9 10 11 12 13 14 15 16 B(A1) XOO 20 7 REMOTE B(A2) 4 21 4-20mA INPUT 8 TERMINAL BLOCK TB3 5 9 RUN REVERSE 10 W(A1) W(A2) 22 CR1 6 RUN FORWARD 7 COMMON 11 19-17 SS2 12 13 8 TB3/KEYPAD OR COMMUNICATION CONTROL 14 15 9 16 CUSTOMER PLC OUTPUT CR1 17 10 19-1
Notes 26
Twenty-Four Volt DC (24VDC) Control Interface for Analog and Preset Drives Power Distribution and DS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Operator Interface Options DN2C, RS1C, P1C, RPAC, P2C, and Ready/Fault Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Enclosure Mounted DeviceNet Connector Options: DNSC1, DNSC2, DNBC1, DNBC2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Distribution and DS Option A B C D E F G H 1 1 BRAKE 1C 2 2 L2 * 1PH, 50/60HZ AC LINES 3 4 L1 5 1 DISCONNECTING MEANS AND SHORT CIRCUIT PROTECTION PROVIDED BY OTHERS WHEN DS OPTION IS NOT ORDERED L2 6 3PH, 50/60HZ AC LINES 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 3 L3 17-18 17-37 L3 4 LINE FILTER 2 4 5 MX14 OPTION 5 6 MODULE 3 6 7 LINE PE 8 POWER DISCONNECTING OPTION 9 DS OPTION 10 CHASSIS EA1 GRD R S TERMINAL BLOCK TB1 E
Drive Ratings and DS Option Ratings A B C D E F G H 1 1 TABLE 1 2 2 3 3 SINGLE PHASE 4 4 FUSE RATINGS (DS OPTION) DRIVE RATINGS CATALOG NO. VOLTAGE (HP) FLA 5 LINE FILTER MODULE CATALOG NUMBER TYPE AMP VOLT 6 160S-AA02* (.5) 160S-AA03* (.75) 160S-AA04* (1) 160S-AA08* (2) 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 200-240V 200-240V 200-240V 200-240V 2.3A 3.0A 4.5A 8.
D13 Without P2C A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND 5 5 RUN REVERSE 6 6 RUN FORWARD 10 AUTO 20 (3) (XOO) (4) 11 21 12 NOTE 1: (3) (4) (OOX) 7 7 COMMON 8 8 TB3
D13 With P2C A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND AUTO 20 (3) (OOX) 5 5 RUN REVERSE 6 6 RUN FORWARD 10 2-WIRE DEVICE 11 (4) 12 * NOTE 1: (3) (4) (XOO) 7 7 COMMON
D17 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 5 5 REVERSE 6 6 START 10 START 20 (3) (4) 11 21 PB2 12 NOTE 1: 7 7 COMMON 8 8 STOP 13 STOP (1) (2) 14 22 PB3 15 9 9 10 1
D32 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 FORWARD (3) (OX) START 20 9 TERMINAL BLOCK TB3 REVERSE 23 (4) 5 5 REVERSE 6 6 START 10 SS3 11 21 * 12 NOTE 1: 7 7 COMMON 8 8 STOP 13 STOP 14 22 *
D33 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 10 5 5 RUN REVERSE 6 6 RUN FORWARD 2-WIRE DEVICE 11 12 * NOTE 1: LOCAL 20 (3) (OX) REMOTE 22 (4) 7 7 COMMON 8 8 TB3/KEYPAD OR COMMUN
D13 and D32 Without P2C A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 OFF HAND AUTO FORWARD 20 (3) (XOO) (4) 21 (3) (OX) (1) (XO) (2) (3) (4) 5 RUN REVERSE 6 6 RUN FORWARD 10 SS3 12 7 7 COMMON 8 8
D13 and D32 With P2C A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 AUTO CONTROL OFF HAND AUTO 20 (3) (OOX) (4) 2-WIRE DEVICE 21 FORWARD 23 (3) (OX) 9 TERMINAL BLOCK TB3 REVERSE 24 (4) 5 5 RUN REVERSE 6 6 R
D17 and D32 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 FORWARD (3) (OX) START 20 (3) (4) 9 TERMINAL BLOCK TB3 REVERSE 23 (4) 5 5 REVERSE 6 6 START 10 SS3 11 21 PB2 12 NOTE 1: 7 7 COMMON 8 8 STOP
D32 and D33 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 2-WIRE DEVICE FORWARD (3) 9 TERMINAL BLOCK TB3 REVERSE 23 (4) (OX) 5 5 RUN REVERSE 6 6 RUN FORWARD 10 * (1) (2) 11 24 SS3 (XO) 12 NOTE 1: LOCAL
D35 and D36 Without Keypad or Comm Control Options A B C D E F G H TABLE 2 1 OPTION SYMBOL COLOR LEGEND PAR 47 SETTING 1 2 D35 D36 PL3 PL4 WHITE RED DRIVE RUN DRIVE FAULT 2 0 (DEFAULT) 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9
D35 and D36 With Keypad or Comm Control Options A B C D E F G H TABLE 2 1 OPTION SYMBOL COLOR LEGEND PAR 47 SETTING 1 2 D35 D36 PL3 PL4 WHITE RED DRIVE RUN DRIVE FAULT 2 0 (DEFAULT) 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 T
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options 10 10 A STOP 19 (PAR 46 = 0) 19 INPUT MODE 0 18 18 11 11 B DR. DATE LEAD ENG. DATE APP'D DATE ACAD 02-02-99 WTG 02-09-99 BAH 02-02-99 REFERENCE DWG.
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options A B C D E F G H 1 1 2 2 3 24VDC INTERFACE 4 5 SPEED REF.
MX12 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 LOCAL CONTROL OFF RUN FWD 20 (B)A1 21 (B)A2 R (OX) SS2 RUN REVERSE 6 6 RUN FORWARD 12 REMOTE 22 (B)A2 7 7 COMMON 8 8 TB3/KEYPAD OR COMMUN
MX14 A B C D E F G H 1 1 24VDC INTERFACE 2 + 3 - CUSTOMER SUPPLIED AND PROTECTED 24VDC 2 ANALOG SIGNAL FOLLOWER 3 160 CONTROL BOARD TB3 TB3 4 1 1 +10V POT 4 5 2 2 WIPER/0-10VDC INPUT 5 6 3 3 COMMON 6 4 4 4-20mA INPUT 5 5 RUN REVERSE 6 6 RUN FORWARD 7 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 10 11 * WTS277 \ 0001 NOTE 2: LOCAL (OX) 7 7 COMMON 8 8 TB3/KEYPAD OR COMMUNICATION CONTROL 12 REMOTE 13 * 14 31 FROM 1-
MX19 A B C D E F G H + 1 - CUSTOMER SUPPLIED AND PROTECTED 24VDC 1 24VDC INTERFACE 2 3 2 ANALOG SIGNAL FOLLOWER 3 160 CONTROL BOARD TB3 TB3 4 1 1 +10V POT 4 5 2 2 WIPER/0-10VDC INPUT 5 3 3 COMMON 6 4 4 4-20mA INPUT 5 5 RUN REVERSE 6 6 RUN FORWARD 6 OFF LOCAL 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 20 REMOTE B(A1) XOO 7 B(A2) 21 8 TERMINAL BLOCK TB3 W(A1) W(A2) 22 9 10 CR1 11 18-17 SS2 NOTE 2: 7 7 COMMON
Notes 46
One Hundred Twenty Volt AC (120VAC) Control Interface for Analog and Preset Drives Power Distribution and DS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Operator Interface Options DN2C, RS1C, P1C, RPAC, P2C, and Ready/Fault Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Enclosure Mounted DeviceNet Connector Options: DNSC1, DNSC2, DNBC1, DNBC2 . . . . . . . . . . . . . . . . . . . . . . .
Power Distribution and DS Option A B C D E F G H 1 1 BRAKE 1C 2 2 L2 * 1PH, 50/60HZ AC LINES 3 4 L1 5 1 DISCONNECTING MEANS AND SHORT CIRCUIT PROTECTION PROVIDED BY OTHERS WHEN DS OPTION IS NOT ORDERED L2 6 3PH, 50/60HZ AC LINES 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 3 L3 17-18 17-37 L3 4 LINE FILTER 2 4 5 MX14 OPTION 5 6 MODULE 3 6 7 LINE PE 8 POWER DISCONNECTING OPTION 9 DS OPTION 10 CHASSIS EA1 GRD R S TERMINAL BLOCK TB1 E
Drive Ratings and DS Option Ratings A B C D E F G H 1 1 TABLE 1 2 2 3 3 SINGLE PHASE 4 4 FUSE RATINGS (DS OPTION) DRIVE RATINGS CATALOG NO. VOLTAGE (HP) FLA 5 LINE FILTER MODULE CATALOG NUMBER TYPE AMP VOLT 6 160S-AA02* (.5) 160S-AA03* (.75) 160S-AA04* (1) 160S-AA08* (2) 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 200-240V 200-240V 200-240V 200-240V LPJ LPJ LPJ LPJ 2.3A 3.0A 4.5A 8.
D13 Without P2C A B C D E F G H 1 1 2 2 24VDC INTERFACE 3 + - CUSTOMER SUPPLIED AND PROTECTED 24VDC 4 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND 10 5 5 RUN REVERSE 6 6 RUN FORWARD AUTO 20 (3) (XOO) (4) 11 21 12 NOTE 1: (3) (4) (OOX) 7 7 COMMON 8 8 TB3
D13 With P2C A B C D E F G H 1 1 2 2 24VDC INTERFACE 3 + - CUSTOMER SUPPLIED AND PROTECTED 24VDC 4 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 OFF HAND AUTO 20 (3) (OOX) 5 5 RUN REVERSE 6 6 RUN FORWARD 10 2-WIRE DEVICE 11 (4) 12 * NOTE 1: (3) (4) (XOO) 7 7 COMMON
D17 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 5 5 REVERSE 6 6 START 10 START 20 (3) (4) 11 21 PB2 12 NOTE 1: 7 7 COMMON 8 8 STOP 13 STOP (1) (2) 14 22 PB3 15 9 9 10 1
D32 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 FORWARD (3) (OX) START 20 9 TERMINAL BLOCK TB3 REVERSE 23 (4) 5 5 REVERSE 6 6 START 10 SS3 11 21 * 12 NOTE 1: 7 7 COMMON 8 8 STOP 13 STOP 14 22 *
D33 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 10 5 5 RUN REVERSE 6 6 RUN FORWARD 2-WIRE DEVICE 11 12 * NOTE 1: LOCAL 20 (3) (OX) REMOTE 22 (4) 7 7 COMMON 8 8 TB3/KEYPAD OR COMMUN
D13 and D32 Without P2C A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 OFF HAND AUTO FORWARD 20 (3) (XOO) (4) 21 (3) (OX) (1) (XO) (2) (3) (4) 5 RUN REVERSE 6 6 RUN FORWARD SS3 12 7 7 COMMON 8 8 TB3/
D13 and D32 With P2C A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 AUTO CONTROL OFF HAND AUTO 20 (3) (OOX) (4) 2-WIRE DEVICE 21 FORWARD 23 (3) (OX) 9 TERMINAL BLOCK TB3 REVERSE 24 (4) 10 5 5 RUN REVERSE 6
D17 and D32 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 FORWARD (3) (OX) START 20 (3) (4) 9 TERMINAL BLOCK TB3 REVERSE 23 (4) 5 5 REVERSE 6 6 START 10 SS3 11 21 PB2 12 NOTE 1: 7 7 COMMON 8 8 STOP
D32 and D33 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 2-WIRE DEVICE FORWARD (3) 9 TERMINAL BLOCK TB3 REVERSE 23 (4) (OX) 10 5 5 RUN REVERSE 6 6 RUN FORWARD * (1) (2) 11 24 SS3 (XO) 12 NOTE 1: LOCAL
D35 and D36 Without Keypad or Comm Control Options A B C D E F G H TABLE 2 1 OPTION SYMBOL COLOR LEGEND PAR 47 SETTING 1 2 D35 D36 PL3 PL4 WHITE RED DRIVE RUN DRIVE FAULT 2 0 (DEFAULT) 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9
D35 and D36 With Keypad or Comm Control Options A B C D E F G H TABLE 2 1 OPTION SYMBOL COLOR LEGEND PAR 47 SETTING 1 2 D35 D36 PL3 PL4 WHITE RED DRIVE RUN DRIVE FAULT 2 0 (DEFAULT) 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 T
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options 10 10 A STOP 19 (PAR 46 = 0) 19 INPUT MODE 0 18 18 11 11 B DR. DATE LEAD ENG. DATE APP'D DATE ACAD 02-02-99 WTG 02-09-99 BAH 02-02-99 REFERENCE DWG.
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options A B C D E F G H 1 1 2 2 24VDC INTERFACE 3 4 5 SPEED REF.
MX12 A B C D E F G H 1 1 2 2 3 + 4 24VDC INTERFACE - CUSTOMER SUPPLIED AND PROTECTED 24VDC 3 ANALOG SIGNAL FOLLOWER 4 160 CONTROL BOARD TB3 TB3 1 1 +10V POT 5 6 2 2 WIPER/0-10VDC INPUT 6 7 3 3 COMMON 7 4 4 4-20mA INPUT LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 5 8 9 10 11 12 13 14 15 16 8 9 TERMINAL BLOCK TB3 LOCAL CONTROL OFF RUN FWD 20 (B)A1 21 (B)A2 R (OX) SS2 RUN REVERSE 6 6 RUN FORWARD 10 12 REMOTE 22 (B)A2 7 7 COMMON 8 8 TB3/KEYPAD OR C
MX14 A B C D E F G H 1 1 24VDC INTERFACE 2 + 3 - CUSTOMER SUPPLIED AND PROTECTED 24VDC 2 ANALOG SIGNAL FOLLOWER 3 160 CONTROL BOARD TB3 TB3 4 1 1 +10V POT 4 5 2 2 WIPER/0-10VDC INPUT 5 6 3 3 COMMON 6 4 4 4-20mA INPUT 5 5 RUN REVERSE 6 6 RUN FORWARD 7 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 10 11 * WTS277 \ 0001 NOTE 2: LOCAL (OX) 7 7 COMMON 8 8 TB3/KEYPAD OR COMMUNICATION CONTROL 12 REMOTE 13 * 14 31 FROM 1-
MX19 A B C D E F G H + 1 - CUSTOMER SUPPLIED AND PROTECTED 24VDC 1 24VDC INTERFACE 2 3 2 ANALOG SIGNAL FOLLOWER 3 160 CONTROL BOARD TB3 TB3 4 1 1 +10V POT 4 5 2 2 WIPER/0-10VDC INPUT 5 3 3 COMMON 6 4 4 4-20mA INPUT 5 5 RUN REVERSE 6 6 RUN FORWARD 6 OFF LOCAL 7 LAMINATED DRAWING MUST BE RE-ISSUED TO SHOP AFTER ECN 8 9 10 11 12 13 14 15 16 20 REMOTE B(A1) XOO 7 B(A2) 21 8 TERMINAL BLOCK TB3 W(A1) W(A2) 22 9 CR1 10 11 18-17 SS2 NOTE 2: 7 7 COMMON
Material List for Spare Parts A B C D E F G H 1 1 REPLACEMENT COMPONENTS LIST 2 EA1 F1-F3 DS RF1 P1 P2 DN2 RS1 DMPS1 DMSF1 LTN120 LTN120 SS1 SS2 SS3 PB2 PB3 PL3 PL4 RH1 1C IB1 PD1 DNR DRIVE FUSES DISCONNECT LINE FILTER PROG. KEYPARD OP INTRF MOD DEVICENET MOD SERIAL COMM. MOD.
www.rockwellautomation.com Power, Control and Information Solutions Headquarters Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA,Tel: (1) 414.382.2000, Fax: (1) 414.382.
