Configuration Option Module Installation

ManualsBrandsRockwell Automation ManualsEquipment150-SM6 SMC-50 Soft Starter Parameter

(Cat 150-SM6)

SMC-50 Parameter Configuration Option Module

Installation Instructions

PN-164974

DIR 10000152879 (Version 01)

Publication 150-IN053B-EN-E

Printed in U.S.A.

* only one 150-SM6 per controller

I/O Port Compatibility*

7 8 9

ok ok ok

90°

0.45 Nm

(4 lb-in)

N223

25U6

IND. CONT. EQ.

WARNING: To prevent electrical shock, disconnect from power source before

installing or servicing. Install in a suitable enclosure. Keep free from contaminants.

Summary of content (6 pages)

PAGE 1
SMC-50 Parameter Configuration Option Module Installation Instructions (Cat 150-SM6) N223 25U6 IND. CONT. EQ. WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in a suitable enclosure. Keep free from contaminants. 1 I/O Port Compatibility* 2 7 8 9 ok ok ok * only one 150-SM6 per controller 0.45 Nm (4 lb-in) 90° 1 7 2 8 9 3 4 1 2 PN-164974 DIR 10000152879 (Version 01) Publication 150-IN053B-EN-E Printed in U.S.A.
PAGE 2
5 2 1 2 90° 1 DIP Switch and Rotary Switch Locations S1 2 F01 7 45 23 I/O 45 23 8 4 5 6 DEVICE 3 45 23 DEVICE 6 2 89 67 A 5 F01 4 1 7 8 F01 89 67 A 3 OPEN BCDE 89 67 A 2 8 PROTECTION 1 7 S4 BCDE S5 PROTECTION 6 89 67 A 5 MFG DATE yy/mm/dd OPEN MFC LOC FACxx I/O S3 BCDE F01 S1 Initial Torque S2 Current Limit S3 Ramp Time S4 Stop Time S5 Motor FLC F01 SMC-50 PARAMETER CONFIGURATION S2 BCDE 4 A 3 SER. OPEN CAT.
PAGE 3
150-SM6 Switch Position Identification: The following defines the functions of the 5 Rotary Switches: S1 = Initial Torque Configuration: Rotary Switch S1 Position Setting 0 1 2 3 4 5 6 7 8 9 A B C D E F Resulting Initial Torque Value (in % Motor Torque) 10 16 22 28 34 40 46 52 58 64 70 (Default) 76 82 88 94 100 S2 = Current Limit Configuration: Rotary Switch S2 Position Setting 0 1 2 3 4 5 6 7 8 9 A B C D E F Resulting Current Limit Value (in % Motor FLC) 200 220 240 260 280 300 320 340 360 (Default) 380
PAGE 4
S5 = Motor FLC (Full Load Current) Configuration: % of Controller’s Max FLC (1) (2) 40 (Default) 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100 Rotary Switch S5 Position Setting 0 1 2 3 4 5 6 7 8 9 A B C D E F (1) Since a set of switches do not provide the resolution to enter all possible Motor FLC combinations like a keypad, Switch S5 allows you to configure the Motor’s FLC in the SMC50 by using a percent (%) of the- controllers raed (e.g 90A, 110A, 140A, 180A, etc) FLC.
PAGE 5
(1) When the "Stop Mode" is configured as a) "Linear Speed Decel", b) "Soft Stop" or c) "Pump Stop" and the "Stop Time" (Rotary Switch S4) is set to 0 a “Coast” to stop will result. A non-zero “Stop Time” value for the 3 previously listed “Stop Modes” defines the time to stop period based on that specific configuration.
PAGE 6
PN-164974 DIR 10000152879 (Version 01) Publication 150-IN053B-EN-E Printed in U.S.A.