Operating NFPA Handle for K-Frame User guide

ManualsBrandsRockwell Automation ManualsEquipment140U-K-NVMxxx NFPA 79 Internal Rotary

BULLETIN 140U

(K-FRAME)

INSTRUCTION SHEET

1 1025144

42053-007

N/A

REVISION

AUTHORIZATION

DR.

CHKD.

APPD.

DATE

E - DOC

LOCATION: MILWAUKEE, WISCONSIN U.S.A.

B-vertical.ai

DWG.

SIZE

SHEET

1234 56 78

REFERENCE

DIMENSIONS APPLY BEFORE

SURFACE TREATMENT

(DIMENSIONS IN INCHES)

TOLERANCES UNLESS

OTHERWISE SPECIFIED

.XX:

.XXX:

ANGLES:

42053

G. Ushakow 12-04-06

12-04-06

M. Jutz

S. Lasko

ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.

Installation Instructions for Bulletin 140U NFPA 79

Internal Rotary Operating NFPA Handle

(Cat 140U-K-NVM12B, -NVM12R, -NVM21B, -NVM21R)

THIS DRAWING IS THE PROPERTY OF

ROCKWELL AUTOMATION, INC.

OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,

USED OR DISCLOSED FOR ANY PURPOSE

EXCEPT AS AUTHORIZED IN WRITING BY

ROCKWELL AUTOMATION, INC.

Cut shaft and tube to proper length

L = D - 127 mm

T = L - 139 mm

(T = L - 5.5 in)

(L = D - 5 in)

MIN

without Bracket = 257 mm (10-1/8 in)

Summary of content (4 pages)

PAGE 1
2 A 3 4 5 6 7 8 Installation Instructions for Bulletin 140U NFPA 79 Internal Rotary Operating NFPA Handle (Cat 140U-K-NVM12B, -NVM12R, -NVM21B, -NVM21R) ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing. B C 1 Cut shaft and tube to proper length L = D - 127 mm (L = D - 5 in) D D DMIN without Bracket = 257 mm (10-1/8 in) E T = L - 139 mm (T = L - 5.
PAGE 2
1 2 3 4 5 6 7 8 A 2 3 Install Assembly Operate Switch Important: Check for full range of motion. B 1 2 1 2 2.0 - 2.25 Nm (18 - 20 lb-in) C 3.2 Nm (28 lb-in) D 3.2 Nm (28 lb-in) TOP E TOP (2) G REFERENCE REVISION AUTHORIZATION 1 1025144 BULLETIN 140U (K-FRAME) INSTRUCTION SHEET DIMENSIONS APPLY BEFORE SURFACE TREATMENT (DIMENSIONS IN INCHES) TOLERANCES UNLESS OTHERWISE SPECIFIED .XX: N/A .XXX: N/A E - DOC THIS DRAWING IS THE PROPERTY OF ROCKWELL AUTOMATION, INC.
PAGE 3
1 2 3 4 5 6 7 8 A 4 Locate Operating Handle in Enclosure Door B 1 C 2 D E 3 (3) G REFERENCE REVISION AUTHORIZATION 1 1025144 BULLETIN 140U (K-FRAME) INSTRUCTION SHEET DIMENSIONS APPLY BEFORE SURFACE TREATMENT (DIMENSIONS IN INCHES) TOLERANCES UNLESS OTHERWISE SPECIFIED .XX: N/A .XXX: N/A E - DOC THIS DRAWING IS THE PROPERTY OF ROCKWELL AUTOMATION, INC.
PAGE 4
1 2 3 4 5 6 7 8 A 4 Locate Operating Handle in Enclosure Door (cont'd) B C 3 D 4 2.8 Nm (25 lb-in.) E 42053-007-01 (1) Printed in U.S.A. -01 1 G PART CHG. NO. CHAR. TWO SIDES PRINTED BODY STOCK WHITE BODY INK BLACK MATERIAL 17" W x 11" H 4-1/4" W x 5-1/2" H FLAT FOLDED SIZE REFERENCE REVISION AUTHORIZATION 1 1025144 BULLETIN 140U (K-FRAME) INSTRUCTION SHEET DIMENSIONS APPLY BEFORE SURFACE TREATMENT (DIMENSIONS IN INCHES) TOLERANCES UNLESS OTHERWISE SPECIFIED .XX: N/A .